Air conditioner kW output vs electricity usage: working out the running cost
The kW on an air conditioner is its output, not its electricity use. How to read the energy label and work out a running cost from your own tariff.
Last updated
The kW figure an air conditioner is sold by is its output: how much heating or cooling it delivers. It is not the electricity it draws. A reverse cycle air conditioner moves heat instead of making it, so when it heats it can deliver three to five times the electricity it uses. Your bill depends on the energy it uses over time, in kilowatt hours (kWh), multiplied by your tariff.
How to use this guide
What is the difference between kW output and electricity usage?
Four figures get mixed up. Only the last two set what you pay.
| Figure | What it means | Where you find it |
|---|---|---|
| Output capacity, in kW | How much heating or cooling the unit can deliver. A higher figure heats or cools a bigger space. | At the top of the energy label. |
| Power input, in kW | The electricity the unit draws while it delivers that output. | The maker's specification sheet. |
| Energy use, in kWh | Electricity used over time. One kW drawn for one hour is one kWh. This is what your meter counts. | The energy label gives a yearly figure for each climate zone. |
| Tariff, in dollars per kWh | What your retailer charges for each kWh. | Your electricity bill. |
So a system sold as 7 kW does not use 7 kWh for every hour it runs. It delivers up to 7 kW of heating or cooling and draws a fraction of that. A plain electric heater is different: it turns each unit of electricity into about one unit of heat, which is why a reverse cycle system costs far less to run for the same warmth.
How do I read the energy label for running costs?
The Zoned Energy Rating Label (opens in a new tab) is the place to start, because it has already turned capacity and efficiency into energy use. It rates each model for three climate zones: hot, average and cold. Use the figures for your own zone, which the Energy Rating Calculator helps you find.
| On the label | What to do with it |
|---|---|
| Output capacity | At the top, in kW, for cooling and for heating. Check it matches the size you were quoted. |
| Yearly energy use | After the stars, in kWh, for each zone: cooling in blue and heating in red. Add the two for your zone. |
| Star rating | More stars means more efficient, compared with models of a similar size. Stars on models of different capacity cannot be compared. |
| Noise | In decibels, with separate indoor and outdoor figures for a split system. |
Choose the size and the features you need first, then use the stars to compare similar models. Of two models with the same stars, the larger one still uses more electricity.
Not every system carries the label. As at November 2026, Energy Rating (opens in a new tab) says it has to be displayed in stores on single-phase, non-ducted air conditioners up to 30 kW, and that ducted systems, multi-split systems and three-phase systems do not have to carry it. It is not mandatory online either. For those, ask the installer for the maker's data sheet with the capacity and the power input.
What does the label assume?
The yearly figure is an estimate for a typical year in each zone, not a measurement of your house. The label assumes these hours of use:
| Climate zone | Cooling season | Heating season |
|---|---|---|
| Hot | 2,247 hours | 277 hours |
| Average | 840 hours | 1,921 hours |
| Cold | 545 hours | 2,660 hours |
If you run yours for fewer hours, or only for cooling, your energy use will be lower than the label. If the house is draughty or the system runs all day, it will be higher. That is why the worksheet asks for your own hours and a figure from your own bill.
How do I work out the running cost?
Energy Rating gives the method: yearly running cost equals the total energy use for cooling and heating, in kWh, multiplied by your tariff in dollars per kWh. Your tariff is in the calculation section of your electricity bill.
A worked example
Step 1: Energy use
Say the label for your zone shows 300 kWh a year for cooling and 1,100 kWh for heating. That is 1,400 kWh.
Step 2: Tariff
Take a flat rate of $0.3198 per kWh, which is one published Victorian default rate.
Step 3: Cost
1,400 multiplied by 0.3198 is about $448 a year.
The tariff in that example is the Victorian Default Offer (opens in a new tab) flat usage charge for the AusNet Services distribution zone, set by the Essential Services Commission for 1 July 2026 to 30 June 2027 and including GST. It is there to show the sum. Use the rate on your own bill: a market offer, a time of use tariff or your own solar power changes the answer.
For a rough hourly figure at the rated output, multiply the power input in kW by your tariff. Most split systems are inverter models, which speed up and slow down with demand, so the draw at any moment varies. The yearly figure on the label is the better guide.
What changes what you actually pay?
| What changes it | How |
|---|---|
| The temperature you set | Each degree of extra heating in winter or cooling in summer adds about 5 to 10 per cent to the energy used. |
| The size of the system | A system that is too large or too small for the space uses energy it does not need to. |
| The filters | Dirty filters cut the airflow and the efficiency of the unit. |
| The house | Insulation, draughts, shade and window coverings set how much heating and cooling the rooms need. |
| The hours it runs | A timer stops it running when nobody needs it. |
| The climate | The same model uses a different amount of energy in each zone, which is why the label is zoned. |
How do I compare the long-term cost of two systems?
Put the purchase and the running cost on one line for each system, with the same assumptions for both:
- the installed price from the quote
- the yearly running cost: the label's energy use for your zone, multiplied by your tariff
- the number of years you expect to keep it. An air conditioner usually lasts 10 to 15 years
- the installed price, plus the yearly running cost multiplied by those years
Write the assumptions down beside the answer: the tariff, the zone, the years. The result is a comparison of two systems under the same assumptions, not a forecast of your bills. Tariffs change, and so does how a household uses a system. A dearer, more efficient model wins this comparison only where it runs for enough hours to earn the difference back.
To compare the quotes themselves, see the guide to comparing air conditioning installation quotes.
How do I check running costs after moving house?
With a system you did not choose, build a baseline before you judge it:
- Write down the brand and the model number from the label on each unit. Your manual shows where it is.
- Look the model up in the Energy Rating Calculator. Older models may not have zoned figures.
- Clean the filters the way the manual shows, so you are measuring the system and not a blockage.
- Compare the kWh on a bill from a season of heavy use with one from a mild season. Heating and cooling usually use the most energy in a household, so the gap between the two bills gives you a rough baseline.
- Note the hours you run it and the temperature you set, then change one thing at a time.
If the bills look high for the hours it runs, a service is the next step, not a guess at a fault. Our air conditioner service page explains what one covers.
Running cost worksheet
Who to ask about a new system
We install and replace split and ducted systems in Bairnsdale and East Gippsland, and we look at the site before we quote. Our air conditioning page explains how to ask for one.
Sources (8)
Checked on 19 November 2026
- Energy Rating: understand the Zoned Energy Rating Label (opens in a new tab)
- Energy Rating: heating and cooling (opens in a new tab)
- Your Home: heating and cooling (opens in a new tab)
- Victorian Government: choosing the right reverse cycle air conditioner (opens in a new tab)
- Essential Services Commission: Victorian Default Offer tariffs, 2026-27 (opens in a new tab)
- CHOICE: how to buy the best air conditioner (opens in a new tab)
- Daikin Australia: is it time to replace or repair your air conditioner? (opens in a new tab)
- ABL Refrigeration: air conditioning services (opens in a new tab) ABL's own page.
Related pages
- How to compare air conditioning installation quotes
Line two quotes up item by item before you compare running costs.
- Sizing a home air conditioner: room boundaries, loads and quote assumptions
How the output a room needs is worked out.
- Repair or replace an air conditioner: how to compare the two quotes
Where running cost fits in a repair or replace decision.
Want a technician to look at it?
Call ABL or send an enquiry. Have your notes ready: the brand, the model and what the unit is doing.
Filled in the record? Copy or print it first: it is not sent with a call or an enquiry.
