Air conditioner will not turn on or respond: what to record
What to look at and write down when an air conditioner will not start, stop or answer its remote, with a status record to fill in before you call.
Last updated
If your air conditioner will not turn on, the usual reasons are no power reaching it, a timer, the remote, or a short delay the unit applies to protect itself. Check those from the outside before you call, and write down what you find. If none of them is the reason, the next step is a technician.
How to use this guide
What to look at when an air conditioner will not turn on
Work down these checks in order. They are the ones we ask about on the phone, and none of them means opening the unit. Write down what you find as you go.
| Check | What to do, then write down |
|---|---|
| Whether the power has been off | Think back over the last day: a power cut, a storm, flickering lights, or work on the house wiring. Write down what happened and when. If the trouble began with an outage, the guide to air conditioner problems after a power outage covers what to do next. |
| The safety switch and the breaker | Energy Safe Victoria's advice for a home that has lost power is to check whether the safety switch has tripped (opens in a new tab) and, if it has, to reset it. If it will not reset, call a licensed electrician. Then look at the air conditioner's own breaker: it should be on. A switch that goes off again is a reason to stop and call. Write down what you found and what you did. |
| The isolating switch at the outdoor unit | Most systems have an isolating switch on or beside the outdoor unit. Check that it is on. If someone has switched it off, ask them why before you switch it on. Write down how you found it. |
| The power point, if it has one | Some units plug in. Look at whether the plug is in and the power point is on. Write down what you saw. |
| The timer | A timer that is set holds the unit off until its time comes. Look at the controller for a timer or schedule, and cancel one you did not mean to set. Write down any on or off times it showed. |
| The batteries in the remote | A faint or blank display on the remote means flat batteries. Replace all of them with new alkaline batteries, the right way round. Rechargeable ones are not suitable. Write down when they were last changed. |
| The lights on the indoor unit | Look at which lights are on, off or flashing, and what colour each one is. Write down what you see before it changes. |
| Which controller you used | Write down whether you were using the handheld remote, a controller on the wall or a phone app. If you had already tried another one, note what it did. |
What usually causes an air conditioner not to turn on?
Most of the time it is one of these. The first six are things you can deal with from the outside. Details differ between models, so check the manual for yours.
| Cause | What is going on | Who deals with it |
|---|---|---|
| No power is reaching the unit | A safety switch, a breaker or the isolating switch is off, a plug is out, or the power has failed. | You, with the checks in the table above. |
| A timer is holding it off | An on timer or a schedule tells the unit to wait. | You, at the controller. |
| The remote, not the unit | Flat batteries, batteries in the wrong way round, another remote in use nearby, strong lighting or a television close to the unit, or sunlight on its receiver. | You. Fit new batteries, move closer to the indoor unit and try again. |
| The restart delay | A unit that has just stopped waits about three minutes before it will run again, to protect itself. | You. Wait a few minutes, then try once. |
| A power cut | Most units restart by themselves a few minutes after the power returns. The clock and the timers are often wrong afterwards. | You. See the guide to air conditioner problems after a power outage. |
| Units set to opposing modes | On a multi-split, one indoor unit cannot heat while another cools. The unit switched on last waits in standby, and on some models its light blinks. | You. Set the indoor units to the same mode, as the manual for your model describes. |
| The unit has stopped itself | A blinking operation light on a unit that will not run often means it has detected a fault. The pattern or the code says which one, and the manual for your model lists them. | A technician. Write down the light or the code, leave the unit off, and call. |
| Something inside the unit | If none of the above explains it, the cause is something no check from the outside will find. | A technician. |
Why does my air conditioner take a few minutes to start?
A short wait is usually the unit protecting itself, not a fault. These are the delays and pauses that are normal.
| What you notice | Why it happens | Write down |
|---|---|---|
| It does not start straight after being switched off, or straight after a change of mode | A unit waits about three minutes after stopping before it will run again, to protect itself. | How long it waited, and whether it then started. |
| It stops by itself with the operation light still on, then starts again | A large swing in the supply voltage makes a unit stop to protect itself. It restarts by itself a few minutes later. | The time, and whether lights elsewhere in the house flickered. |
| It runs, but no operation light shows | On some models the lights on the indoor unit can be dimmed or switched off in the settings. | Whether air is coming out, and which lights are off. |
Times differ a little between models, so check the manual for yours. What to report is a wait much longer than a few minutes, or a unit that does not start.
What if the remote does not control the air conditioner?
Write down what happened when you tried to use it. Do not keep pressing buttons to find out more, and leave blank anything you did not notice:
- which controller you were using: the handheld remote, a controller on the wall or a phone app
- whether the display on the remote is clear, faint or blank
- whether the indoor unit beeped or showed a light when you pressed a button
- whether it ignored every button you had tried, or only some of them
- whether fluorescent lights or a large television are near the indoor unit, and whether sunlight falls on it
If neither the remote nor the on/off button on the unit does anything at all, stop trying. Switch the unit off at its power point or circuit breaker if that is dry and within easy reach, then call.
What does a blinking light on my air conditioner mean?
A blinking light is the unit telling you something, and what it says depends on the make and the model. On some units a flashing light is only a reminder that a filter needs cleaning. On a multi-split it can mean the indoor units are set to opposing modes. Often it means the unit has detected a fault and stopped itself. This guide does not decode it. Write down:
- which light it is, by its label or its position, and its colour
- whether it is steady, flashing slowly or flashing fast, and how many flashes come before a pause
- any letters or numbers on the controller or on the display of the unit
- what the unit was doing when the light started
A photo or a short video of the light helps, taken without touching the unit. Then look the pattern up in the manual for your model, or read it out when you call. A list of codes for another brand or another model will point you the wrong way. For two makes, see the guide to Fujitsu flashing lights and the guide to a flashing Panasonic TIMER light.
Why does the indoor fan keep running after I turn the air conditioner off?
Some units keep the indoor fan running for a while after you switch them off, on purpose: it dries the inside of the unit so mould does not grow there. Check the manual for your model to see whether it has a function like this. Write down:
- which mode it was in before you switched it off
- how long the fan kept running, and whether it stopped by itself
- which lights stayed on while it ran
- whether this is new, or it has done it since it was installed
A fan that does not stop, or a unit that will not switch off from its controller, is one to report. Switch it off at its power point or circuit breaker only if that is dry and within easy reach, and leave it off.
Why has the outdoor fan stopped while the indoor unit is still running?
Some pauses are normal. In heating on a cold day the unit stops now and then to melt frost off the outdoor coil, and both fans stop while it does. A defrost usually takes a few minutes, up to about ten, and the guide to frost on the outdoor unit in winter covers it. In cooling on a cool day the outdoor fan runs on and off. A fan that stays still on a warm day while the indoor unit blows air that is not cold is one to report. Record what you saw from a few steps back. Write down:
- the mode, and how long the system had been running
- whether the outdoor fan was still, turning slowly, or starting and stopping
- whether the indoor unit was still blowing cold or warm air
- any frost, ice, water or steam at the outdoor unit
- any sound from the outdoor unit, and the weather at the time
Stay clear of the fan, and of the pipes and cable at the side of the unit. Do not put anything through the grille to see whether the fan will turn.
Status record for an air conditioner that will not turn on or respond
What will a technician do?
The order depends on what your record shows. When we come out to a unit that will not turn on, we usually:
- read the fault code or the light pattern the unit is showing
- test the power supply to the unit, from the switchboard to the outdoor unit
- test the remote, and the receiver in the indoor unit
- tell you what has failed, what it would take to fix, and whether that is worth doing on a unit of its age
The Australian Refrigeration Council says all servicing and repairs of a home air conditioner must be done by a technician with a full refrigeration and air conditioning licence (opens in a new tab).
How urgent is it?
By itself, an air conditioner that will not turn on is not an emergency. It becomes urgent when a sign from the warning at the top of this guide appears: a burning smell, a switch that will not stay on, or water from the indoor unit. Then leave it off and call. If a blinking light is the only sign and the manual for your model does not explain it, leave the unit off and book a visit.
When to call, and who does the work
Past these checks, the next step is a call. Energy Safe Victoria tells households not to do their own electrical work (opens in a new tab), and says you can and should ask to see a tradesperson's licence. Work on the air conditioner itself is licensed too: in Australia, anyone whose work involves handling a scheduled refrigerant, or a part of the equipment that could release one, must be licensed, as the refrigerant handling code of practice (opens in a new tab) (2025 edition) sets out.
The same code tells owners that a unit that is not working properly should be seen by a competent service technician as soon as the problem appears.
ABL repairs and services air conditioners for homes and businesses in Bairnsdale and East Gippsland. Our air conditioning repairs page explains how to book. Have your status record in front of you when you call.
Sources (11)
Checked on 17 November 2026
- Daikin: troubleshooting for split and multi-split air conditioners (opens in a new tab)
- Daikin Australia: operation manual for FTXM room air conditioners (opens in a new tab)
- Mitsubishi Electric Australia: operating instructions for MSZ-AP split systems (opens in a new tab)
- Mitsubishi Electric Australia: air conditioning defrost cycle (opens in a new tab)
- Mitsubishi Electric Australia: how to clean your air conditioner filter (opens in a new tab)
- Energy Safe Victoria: power outages and energy safety, reviewed 9 April 2024 (opens in a new tab)
- Energy Safe Victoria: working with tradespeople, reviewed 8 September 2026 (opens in a new tab)
- Australian Refrigeration Council, Look for the Tick: home air conditioners (opens in a new tab)
- Australia and New Zealand refrigerant handling code of practice, part 2, 2025 edition (opens in a new tab)
- Australian Government: Triple Zero (000) (opens in a new tab)
- ABL Refrigeration: air conditioning services (opens in a new tab) ABL's own page.
Related pages
- Air conditioner problems after a power outage: settings or safety?
What to do when the trouble started with a power cut or a storm.
- Air conditioner starts then stops: what to log for a technician
What to log when the unit starts, then shuts down again.
- Air conditioner burning smell or tripping breaker: what to do
What to do when a breaker has tripped or there is a burning smell.
Want a technician to look at it?
Call ABL or send an enquiry. Have your notes ready: the brand, the model and what the unit is doing.
Filled in the record? Copy or print it first: it is not sent with a call or an enquiry.
