Air conditioner starts then stops: what to log for a technician
What to log when an air conditioner starts then stops: run time, mode, lights and room conditions, with a stop log to fill in for the technician.
Last updated
An air conditioner that starts and then stops is either pausing the way its manual describes, or short cycling: turning on and off without reaching the set temperature. The usual causes of short cycling are a clogged filter, blocked airflow, a timer, a faulty thermostat, a refrigerant leak, ice on the indoor coil, or a unit too big for the room. Two of those you can check. For the rest, keep a short log for a technician.
How to use this guide
Step 2: Log
Note each stop as it happens in ordinary use. Three or four entries are enough.
Go to the record
Why does my air conditioner start and then stop?
Start with the stops that are not faults. Each of these is a unit doing what it was built to do.
| What you notice | Why it happens | What to log |
|---|---|---|
| It stops by itself with the operation light on, then starts again a few minutes later | A large swing in the supply voltage makes the unit stop to protect itself. It restarts by itself after about three minutes. | The time, how long it was off, and whether lights in the house flickered. |
| The airflow rises and falls, or the unit seems to turn on and off, once the room is near the set temperature | At the set temperature the unit drops to a gentle breeze so the room is not overcooled or overheated. While the room stays near that temperature, the airflow rises and falls. | The set temperature, and the room temperature if you have a thermometer. |
| It will not start again straight after stopping, or after a change of mode | The unit waits about three minutes to protect itself. | How long it waited before it ran. |
| It stops soon after you use the remote, and an on timer is set | With an on timer set, some units start up to an hour early so the room is ready on time. Using the remote during that early run stops it. | The timer setting shown on the controller. |
| Heating stops for a few minutes and you hear water flowing | The outdoor unit is defrosting. It usually takes a few minutes, up to about ten. | How long each pause lasted, and the weather. See the guide to frost on the outdoor unit in winter. |
Times vary a little between models, so check the manual for yours. A stop that matches none of these, or that happens far more often than the manual describes, is what the log is for.
What usually causes an air conditioner to start and then stop?
When a unit turns on and off rapidly without reaching the temperature it is set to, the trade calls it short cycling. These are the usual causes. The first three are yours to deal with. The rest need a technician.
| Cause | What is going on | Who deals with it |
|---|---|---|
| A clogged air filter | The most common cause. A blocked filter chokes the airflow the unit needs. | You, following the manual for your model. |
| Blocked airflow at either unit | Furniture or curtains against the indoor unit, or leaves and clutter around the outdoor unit, do the same. | You, from the outside. Do not reach into either unit. |
| A timer or weekly schedule | A timer you have forgotten switches the unit on and off at its set times. | You, at the controller. |
| A faulty thermostat or sensor | The unit misreads the room temperature and stops too soon. | A technician. |
| Low refrigerant | Refrigerant is not used up, so a low charge means a leak. The unit cannot move heat properly, and its protection shuts it down. | A licensed technician. The leak is found and repaired before any refrigerant goes back in. |
| Ice on the coil inside the indoor unit | Ice blocks the airflow. It usually follows from poor airflow or low refrigerant. | A technician. Note where you can see ice, and do not chip at it. |
| A unit too big for the room | An oversized unit reaches the set temperature quickly and shuts off, again and again. | A technician who can see the room. |
What can I safely check myself?
Three things, all from the outside. If the stops go on afterwards, stop checking and book a visit.
| Check | What to do |
|---|---|
| The timer and any weekly schedule | Look at the controller for a timer or a schedule, and cancel one you did not mean to set. |
| The filters | Switch the unit off at the wall first, then clean the filters the way the manual for your model describes. In daily use they want cleaning about every two weeks. |
| The space around both units | Move furniture, curtains and stored things away from the indoor unit, and leaves and clutter away from the outdoor unit. |
One thing not to do in heating on a cold morning: do not switch the unit off part way through a defrost. Restarting it soon afterwards makes it less efficient and can damage it. A pause of a few minutes with the sound of water is a defrost, and the unit ends it by itself.
When should I stop using it and call?
Some stops are not normal. For each of these, stop using the unit, switch it off at its power point or circuit breaker if that is dry and within easy reach, and call:
- a burnt smell
- a circuit breaker or safety switch that trips, or a fuse that blows
- an abnormal noise from the indoor unit. The guide to air conditioner rattling and vibration noise covers what to record about a sound.
Do not switch it back on to see whether it runs for longer this time. The manual for your model has its own list like this, and that list is the one to follow.
An operation light that flashes when the unit stops is one to report as well. Before you call, note whether the filters are clean and whether anything is blocking the air going into or out of either unit, and write down what the light did.
What should I log each time the air conditioner stops?
Log the stops that happen while you use the unit as usual. Do not restart it over and over to make it stop again: a technician can work from three or four honest entries. For each stop, write down:
- the date and time it started, and how long it ran before it stopped
- the mode and the set temperature on the controller
- what the lights on the indoor unit did when it stopped: steady, flashing or off
- any message or code on the controller
- whether the outdoor unit was running, seen from a few steps back
- whether it started again by itself, and after how long
What else should the technician know about the room and the unit?
The room and the history of the unit help a technician read the log. Add:
- the weather and the outside temperature when it stopped
- whether windows or doors were open, and whether the sun was on the room
- whether anything sits close to the indoor unit, or is stacked against the outdoor unit
- when the filters were last cleaned, as your manual describes
- what changed before it started: a power cut, a storm, a renovation, a new appliance or a service visit
- the date of the last service, who did it, and what the report says was done
- whether it has done this since it was installed, or only recently
Is the unit too big for the room, or low on refrigerant?
Both are on the list of usual causes above, and neither can be confirmed from a description, so the log does not ask you to pick one. Whether the system suits the room is a question for a technician who can see the site.
The same goes for refrigerant. The refrigerant handling code of practice (opens in a new tab) (2025 edition) says a system known to be leaking must not be topped up with refrigerant until the leaks are fixed. So if you are offered a top-up, ask what the leak test found. For what a leak assessment covers, see the guide that answers this question: does a split-system air conditioner need regassing?
Stop log for an air conditioner that starts then stops
What will a technician do?
Your log sets the order. When we come out to a unit that keeps stopping, we usually:
- read any fault code the unit has stored
- check the airflow through both units, and the condition of the filters and coils
- test the thermostat and the temperature sensors
- check the refrigerant and test for leaks
- look at whether the size of the unit suits the room
Where there is a leak, the Australian Refrigeration Council's rule is that all affected parts are repaired or replaced before the unit is refilled (opens in a new tab).
Should I keep using it, and how urgent is it?
If a sign from the warning at the top appears, stop using it now. If the operation light blinks when it stops, or the indoor unit makes an abnormal sound, stop using it and call. A unit whose pauses match the normal ones in the first table can stay in use. If the stops are not those, and the three checks have not ended them, stop using the unit and book a visit. Your log shows us where to start.
Who to call about an air conditioner that keeps stopping
Call once you have a few entries, or straight away if a sign from the warning at the top appears. The refrigerant handling code tells owners that a unit that is not working properly should be seen by a competent service technician as soon as the problem appears, to keep any refrigerant leak small.
ABL repairs and services air conditioners for homes and businesses in Bairnsdale and East Gippsland. Our air conditioning repairs page explains how to book. Read the log out when you call, or paste it into your enquiry.
Sources (10)
Checked on 17 November 2026
- Daikin: troubleshooting for split and multi-split air conditioners (opens in a new tab)
- Daikin Australia: operation manual for FTXM room air conditioners (opens in a new tab)
- Mitsubishi Electric Australia: operating instructions for MSZ-AP split systems (opens in a new tab)
- Mitsubishi Electric Australia: air conditioning defrost cycle (opens in a new tab)
- CHOICE: how to fix and maintain your own air conditioner, updated 26 February 2021 (opens in a new tab)
- CHOICE: how to clean your air conditioner, updated 3 November 2026 (opens in a new tab)
- Australian Refrigeration Council, Look for the Tick: home air conditioners (opens in a new tab)
- Australia and New Zealand refrigerant handling code of practice, part 2, 2025 edition (opens in a new tab)
- Australian Government: Triple Zero (000) (opens in a new tab)
- ABL Refrigeration: air conditioning services (opens in a new tab) ABL's own page.
Related pages
- Air conditioner will not turn on or respond: what to record
What to record when the unit will not start at all, or ignores its remote.
- Air conditioner burning smell or tripping breaker: what to do
What to do when a stop comes with a burning smell or a tripped breaker.
- Air conditioner not cooling or heating: what to check before you call
What to check when the unit keeps running but the room is not comfortable.
Want a technician to look at it?
Call ABL or send an enquiry. Have your notes ready: the brand, the model and what the unit is doing.
Filled in the record? Copy or print it first: it is not sent with a call or an enquiry.
