Replacing a fixed speed air conditioner: how to choose between inverters
How to compare inverter air conditioners to replace an old fixed-speed unit: capacity, seasonal efficiency, minimum output, winter heating and the site.
Last updated
Nearly every split system sold now is an inverter, so replacing a fixed-speed unit means choosing between inverters. An inverter changes its compressor speed to match what the room needs, where your old unit runs flat out and then stops, so the room stays steadier, the unit runs more quietly and it uses less energy when the room needs only part of its output. The word inverter says little about a model on its own. Compare the models you are offered on their real figures, size the new one for the room as it is now, and weigh the old unit's history and the site before you decide.
How to use this guide
Step 1: Know the difference
How a new inverter runs differently from your old unit.
Go to The difference
How do inverter and fixed-speed units differ?
| What differs | Your old fixed-speed unit | A new inverter |
|---|---|---|
| How it controls the output | The compressor runs at full speed until the room reaches the set temperature, then stops, then starts again. | The compressor speeds up and slows down to match what the room needs, and keeps running at a lower output. |
| Temperature in the room | Swings between too warm and too cool as it stops and starts. | Steadier, because the output follows the room. |
| Noise | Louder and more noticeable each time the compressor starts. | Quieter and more even once the room is at temperature. |
| Energy use | Higher, because it runs at full power whenever it runs. | Lower when the room needs only part of the output. |
Fixed-speed split systems are now hard to find new. Of about 1,500 wall-mounted split system models registered for sale in Australia as at November 2026, one is fixed speed. So the choice in front of you is which inverter, not whether to have one.
How much less an inverter costs to run than your old unit depends on the two models, the hours it runs and your tariff, and nobody can promise you a figure. Work it out from the yearly energy use on the label for your climate zone: the guide to air conditioner output and electricity usage has the method and a worksheet.
Which figures should you compare between inverter models?
Two inverter models with the same nominal size can perform quite differently. These are the figures that separate them. Most are on the Zoned Energy Rating Label (opens in a new tab) or in the maker's specification sheet for the model.
| Figure | What it tells you | What to look for |
|---|---|---|
| Capacity, cooling and heating | How much cooling and heating the unit delivers at the rated conditions. The label shows heating at two outdoor temperatures and cooling at one. | A capacity that matches a new load calculation for the room, not the old unit's number. |
| Heating at 2°C outside | How much heat it still delivers in cold weather. Units built for heating hold more of their output below 2°C. | In a cold winter area, the heating capacity at 2°C, not only the rated figure. |
| Seasonal efficiency | How efficient it is across a season, including part load, for your climate zone. TCSPF is the cooling figure and THSPF the heating figure. | A THSPF over 5 is good and over 6 excellent. A TCSPF over 6 is good and over 7 excellent. Weight the one you use most. |
| Minimum output | The lowest output the compressor can hold steadily. Below it, an inverter stops and starts like a fixed-speed unit. | A low minimum, so it can run gently on mild days and overnight. |
| Operating range | The outdoor temperatures the unit is made to work in, for heating and for cooling. | A range that covers the coldest mornings and hottest afternoons where you live. |
| Noise | Indoor and outdoor noise in dB(A). The label figure is at full power. | Figures measured the same way for each model. |
For more on heating output in cold weather, see the guide to rated capacity versus output in very cold weather.
Should the new unit be the same size as the old one?
Not by default. Copying the old unit's capacity can repeat a sizing mistake made when it went in, and the house may have changed since: insulation, new windows, an extension, a room used differently. Ask for a new heat load calculation for the room before you compare models, and ask to see what it assumed.
If the old unit seemed too big, cycling on and off and leaving the room clammy or uneven, the guide to oversized air conditioning covers what to record before it is replaced.
What else belongs in the comparison?
The inverter question is only part of a replacement decision. Put these beside the figures:
- The old unit's history: its age, what has been repaired, and what a technician says is wrong now. Older systems tend to be less efficient, noisier and less reliable, and parts for them are often no longer made. If you are still deciding whether to repair it, see the guide to a repair quote or a replacement quote.
- The pipework: pipework from an older system is generally replaced, because some older refrigerants leave a residue that does not suit new units. See the guide to reusing refrigerant pipework.
- The electrical supply: the wiring and safety switching should be checked against current requirements, and the supply should have the capacity for the new unit.
- The positions: whether the new indoor and outdoor units can go where the old ones were, or whether a better position is worth the extra work.
- The old unit: removing it, and having its refrigerant recovered by a licensed technician, is part of the job.
What does a replacement cost?
As at November 2026, our published guide for a basic split system is $2,000 to $4,000 installed. Your quote is the price. On a replacement, what moves it is the capacity and the efficiency of the new model, new pipework, any electrical work, a change of position, and removing the old unit.
A more efficient model usually costs more to buy and less to run, so the more hours it runs, the more the running cost matters. The guide to comparing AC quotes helps you set two quotes side by side.
Replacement comparison sheet
Fill in the old unit from its nameplate, its manual and what you know of its history, then fill in each option from its label and specification sheet.
Getting a quote
Send us the sheet with your enquiry, with a photo of the old unit's nameplate if you can reach it from the ground, or have it ready when we visit. Our split system installation page explains the job, and our air conditioning page covers everything else we do.
Sources (10)
- AIRAH: Residential Air Conditioning Best Practice Guide (Victoria), second edition 2026 (opens in a new tab) Checked on 19 November 2026.
- Your Home (Australian Government): heating and cooling (opens in a new tab) Checked on 19 November 2026.
- Energy Rating: understanding the Zoned Energy Rating Label (opens in a new tab) Checked on 19 November 2026.
- Hitachi Cooling and Heating Australia: non-inverter and inverter air conditioners (opens in a new tab) Checked on 19 November 2026.
- LG Australia: why use an inverter air conditioner (opens in a new tab) Checked on 19 November 2026.
- Energy Rating data for household appliances: air conditioner registrations, 19 November 2026 (opens in a new tab) Checked on 20 November 2026.
- Australian Government: decision regulation impact statement for air conditioners, December 2018 (opens in a new tab) Checked on 20 November 2026.
- CHOICE: how to buy the best air conditioner, updated 31 July 2026 (opens in a new tab) Checked on 20 November 2026.
- Panasonic Australia: air conditioning buyers guide (opens in a new tab) Checked on 19 November 2026.
- ABL Refrigeration: air conditioning services (opens in a new tab) ABL's own page. Checked on 19 November 2026.
Related pages
- Repair quote or replacement quote for an ageing system?
If you are still deciding whether to replace.
- AC running-cost calculations: output, electricity and labels
How to work out what each option costs to run.
- Rated capacity versus output in very cold weather
Heating output on cold Gippsland mornings.
Replacing an old unit?
Call ABL or send an enquiry, and have your comparison sheet and the old nameplate ready.
Filled in the record? Copy or print it first: it is not sent with a call or an enquiry.
