Skip to the content

Split system installation in Bairnsdale and East Gippsland

ABL supplies and installs split systems in Bairnsdale and East Gippsland. What it costs, what size you need, where the units go and what happens on the day.

Send an enquiry to ask for a quote, or call if you would rather talk it through. Fill in the quote details first: the rooms, the house and where the units could go. ABL then looks at the site before it recommends a size.

How to get a quote

  1. Step 1: Fill in the quote details

    The rooms, the house and where the units could go. Fill in what you can.

    Go to the record
  2. Step 2: Send them to ABL

    Paste them into an enquiry, or call and read them out.

    Call (03) 5153 2650
  3. Step 3: Have the site looked at

    ABL visits, looks at the rooms and the power supply, and then quotes.

    Go to Installation day

What ABL installs

  • a split system for one room or an open living area: one indoor unit on the wall and one outdoor unit
  • a multi-head system: one outdoor unit that runs indoor units in several rooms
  • a replacement for a split system that has come to the end of its life
  • reverse-cycle systems, which heat as well as cool

ABL installs Panasonic split systems. See the Panasonic air conditioning page for that range, and tell us if you have another brand in mind.

To heat and cool a whole house through ducts, see ducted air conditioning. For a shop, an office or a venue, see commercial air conditioning. Our other work is on the air conditioning services page.

What ABL needs for a split system quote

A quote is only as good as what the installer knows about the house. You do not need to measure closely or look inside anything: note what you can see, and leave a field blank if you are not sure.

Split system quote details

Fill in what you can, then paste it into an enquiry or read it out when you call.

Your answers stay on this open page. They are not saved or sent. Copy or print them before you leave.

The house

It is a
Built or renovated before 1990See the note on older homes further down.
Outside walls

The rooms

Ceilings
Ceiling insulation

What is there now

Where the units could go

Access and timing

What size air conditioner do I need?

Floor area is only part of the answer. The right size also depends on ceiling height, insulation, window area, how many people use the room and the local climate. A unit that is too small struggles to hold a comfortable temperature. One that is too large costs more to buy and runs less efficiently.

What sets the size of a split system
What sets the sizeWhat to tell us
Room sizeThe length and width of each room, or its floor area.
Ceiling heightWhether the ceiling is a standard height, high or raked.
InsulationWhether the ceiling and walls are insulated, if you know.
WindowsHow much glass the room has, and which way it faces.
PeopleHow many people use the room, and at what time of day.
ClimateYour town or locality.

As a starting range by room size:

A starting range for split system size
Room sizeUsual capacity
Up to 20 square metres, such as a bedroom or study2 to 3 kW
21 to 40 square metres2.5 to 5 kW
41 to 60 square metres4 to 8 kW
More than 60 square metres5 kW and up, often 8 kW or more

The table is the general range in published guides for households, including the Victorian Government's. Our own guide on the air conditioning page allows more for some rooms: 2.5 to 3.5 kW for a bedroom of 12 to 20 square metres, and 5 to 7 kW for a living area of 20 to 40 square metres.

Read both as starting ranges and not an answer. We settle the size at the site assessment: we look at the rooms themselves, talk through how you use them, and then recommend a capacity.

When you compare models, the Zoned Energy Rating Label (opens in a new tab) shows a model's capacity, energy use and noise. It rates heating and cooling separately for hot, average and cold climate zones, and the Energy Rating Calculator helps you find your zone. For what happens when a system is too large, see the guide to oversized air conditioning.

Multi-head split system or separate split systems?

A multi-head system runs indoor units in several rooms from one outdoor unit. Separate split systems give each room its own indoor unit and its own outdoor unit. ABL installs both.

  • Space outside. A multi-head system needs a place for one outdoor unit, not one for each room.
  • One outdoor unit carries every room. If it stops, every room it serves stops with it. A separate split system affects its own room only.
  • The rooms you want, now and later. Tell us every room you want to heat or cool, and any you might add.

Which one suits your home comes down to the rooms and where the units can go, so we settle it at the site assessment. The guide to single, multi-split or ducted layouts compares them, and the ducted air conditioning page covers whole-house systems.

The licence an installer needs differs too. As at November 2026, Victoria's restricted plumbing class for split systems (opens in a new tab) covers installing and commissioning a single-head split system up to 18 kW of cooling capacity, a ceiling cassette system or an add-on condenser unit for a ducted system, and no other mechanical services work. A multi-head system is not on that list, so ask any installer which class they hold.

Where can the indoor and outdoor units go?

We settle this at the site assessment, and the maker's instructions set the exact clearances. As general guidance:

General guidance on where split system units go
UnitWhere it works bestWhere to avoid
Outdoor unitIn shade or on the south side, close to the indoor unit so the pipes are short, and with good air circulating around it.Beside windows, bedrooms or living areas, yours or a neighbour's. In full sun, where a unit works harder and uses more energy to cool.
Indoor unitOn a longer wall of the room, where its drain can run outside or to a wet area.Directly above a window.

Where the outdoor unit goes matters to your neighbours as well as to you. Under Victoria's residential noise rules (opens in a new tab), as at November 2026, air conditioner noise that a neighbour can hear indoors is unreasonable during prohibited times at night and early in the morning, and the guide to choosing an outdoor unit location gives the times. Tell us where the neighbours' bedrooms are when we look at the site.

  • In a unit or an apartment, ask the owners corporation first. It decides where an air conditioner can go on common property.
  • Under a heritage overlay, ask the council first. Planning Victoria (opens in a new tab) says exterior alterations there generally need a planning permit.
  • Near the coast, say so. An outdoor unit in salt air may need special treatment.

What does split system installation cost?

As at November 2026, a basic home split system usually costs $2,000 to $4,000 installed. Your quote is the price, and ABL gives a free quote with no obligation. Where a job sits in that range, and whether it goes beyond it, depends on the system you choose and on the house.

What changes the cost of a split system installation
What changes the costWhy
Where the two units sitThe simplest job puts the outdoor unit directly behind the indoor unit, which keeps pipework and labour down. Units further apart, on an upper storey or somewhere hard to reach cost more.
The size of the systemA larger system costs more. A small unit for a bedroom sits toward the lower end of the range, and a large unit for an open living area toward the upper end.
Electrical workA new split system should be on its own dedicated circuit, which means some electrical work. A switchboard that needs upgrading adds to it.
Extra pipe and drainageA longer pipe run, or a longer drain run, adds to the job.
Brackets, a slab or a standA wall bracket or a base for the outdoor unit may add to the cost.
An old system to take outRemoving and disposing of an existing system is extra work.

Most of these can only be judged at the house, which is why we look at the site before we quote.

From site assessment to handover

What happens, in order

  1. Step 1: Site assessment

    ABL visits, looks at the rooms and the power supply, talks through what you need and works out where the indoor and outdoor units can go.

  2. Step 2: Recommendation and quote

    We recommend a system and its capacity for those rooms, and quote for the supply and the installation.

  3. Step 3: Installation

    We fit the indoor and outdoor units, run the refrigerant pipes and the electrical connections, see to the drainage and clean up.

  4. Step 4: Testing and handover

    We run the system in each mode, show you how the controller works and answer your questions.

What you should receive after the installation

In Victoria, installing a split system is plumbing work (opens in a new tab) and electrical work, and each has its own document. An Energy Safe Victoria fact sheet (opens in a new tab) says the customer must receive both. Keep them with the manual.

Documents after a split system installation
DocumentWhen it appliesWhen you get it
Plumbing compliance certificatePlumbing work with a total value of $750 or more. The total counts materials, anything installed and labour.The licensed plumber gives it to you, and lodges it, within five days of finishing.
Certificate of Electrical SafetyAll electrical installation work.Air conditioning work is non-prescribed electrical work, and for that you get a copy within 30 days.

These rules are as at November 2026. The plumbing rule is in the Building Act 1993 (opens in a new tab) and explained by the Building and Plumbing Commission (opens in a new tab). The electrical rule is set out by Energy Safe Victoria (opens in a new tab).

Anyone who installs a split system also needs a refrigerant handling licence (opens in a new tab). You can check any technician's licence at Look for the tick (opens in a new tab).

Other questions about installation

How long does a split system installation take?

We allow 4 to 6 hours for a standard home split system. Several systems, or a multi-split, can run over a few days.

What happens to the old air conditioner?

Its refrigerant has to be recovered by a licensed technician before the unit is disposed of, the Australian Refrigeration Council (opens in a new tab) says, and venting it is prohibited. The old equipment then goes for recycling: East Gippsland Shire (opens in a new tab) lists air conditioners with steel and white goods in its waste fees. If there is an old system to take out, say so when you ask for a quote, and ask whether the quote covers its removal.

Does a split system need its own circuit?

Generally, yes. An air conditioner usually needs a dedicated circuit from the switchboard. That is work for a licensed electrician, and it is one reason we look at the power supply at the site assessment.

Can I install a split system myself?

No. You can buy a pre-charged split system without a licence, but the Australian Refrigeration Council (opens in a new tab) says a licence is required to install it, and the electrical work needs a licensed electrician.

Towns ABL covers

ABL is based in Bairnsdale and installs split systems across Gippsland, from Morwell to the New South Wales border. A town with a link has its own page.

If your town is not here, call and ask. See also service areas.

Sources (25)

Want a split system installed?

Send an enquiry with your quote details, or call ABL and talk it through.

Filled in the record? Copy or print it first: it is not sent with a call or an enquiry.