Ice machine making less ice: what to record before you call
Is your ice machine making less, or are you using more? How to tell, what usually lowers output, when to stop using the ice, and a log for the technician.
Last updated
When a commercial ice machine is not making enough ice, first work out whether it is making less or the venue is using more. A machine in good order can make 10 to 30 per cent less in a 32°C room with warm tap water than in a mild one, depending on the model, and a bin that runs out in the evening rush may be too small rather than faulty. Measure what the machine makes, note the room and water temperatures and when the change began, look at what you can see from outside, and call with the log.
How to use this guide
Step 1: Less ice, or more use?
Match what you notice to what it points to.
Go to Less ice, or more use
Is it making less ice, or are you using more?
The pattern of the shortfall says a lot. Match what you notice, and write down what the last column asks for.
| What you notice | What it usually points to | Write down |
|---|---|---|
| The bin runs out in the busiest service, and is full again by morning | The machine is keeping up with the day but not the peak. The bin may be too small for the rush. See the guide to sizing a hospitality ice machine. | When it ran out, how long the service had run, and the level at opening. |
| The shortfall began with the hot weather | Output falls as the room and the water warm up. The machine may be working to its own table and still fall short. | The room temperature beside the machine and the tap water temperature, with the time. |
| It began with more trade | More use: a function, a busier menu, more rooms let, a new cold drink dispenser. | What changed, and when. |
| The bin is lower at opening than it used to be, with the same trade | The machine is making less ice than it did. | The bin level at close and at opening for a few days, and the readings in the next section. |
| The cubes are smaller, thinner or hollow | Often not enough water reaching the machine, a blocked water filter, or scale. | A photo of the cubes, and when the water filter was last changed. |
| It stops before the bin is full | Usually something holding the machine at "full". The ice machines page covers this fault. | Whether ice is stuck at the chute or packed in a lump in the bin. |
How do you measure what the machine makes?
These readings, taken from outside the machine, tell a technician most of what they need before they arrive.
- The bin level at close and at opening. Note how full the bin is at close and again at opening, with nothing taken out between, for a few days. A bin that is full every morning tells us the machine keeps up overnight. A bin that is still low tells us it does not.
- The time between harvests. A cube machine drops its ice in batches. Note the time of two drops in a row: you can usually hear them. A cycle usually runs about 10 to 30 minutes, and longer when the room or the water is warm.
- The weight of one harvest. Leave this to the technician, unless the manual for your model tells the owner how to catch one at the bin door. Do not reach into the machine or past a flap to do it. Some spec sheets print the ice made in each cycle, which does the same job.
With the time between harvests and the weight of one harvest, you can estimate a day's output: the weight of one harvest times the number of harvests in a day, which is 1,440 divided by the minutes between harvests. Compare it with the maker's table at your room and water temperatures. We treat output within about 10 per cent of the maker's table as normal.
If the machine is making what its table says it should, a repair will not give you more ice: the answer is more output, more storage or a cooler spot for the machine. The guide to sizing a hospitality ice machine explains the tables, and the guide to an air-cooled or water-cooled ice machine covers a room that is too hot.
What usually lowers an ice machine's output?
These are the usual causes. They are not a diagnosis of your machine, and cleaning does not fix every one.
| Cause | What you can see from outside | Who deals with it |
|---|---|---|
| A hot room or a hot spot | An oven, a dishwasher, a fryer or direct sun beside the machine. The room temperature on a busy service. | You can move what stands beside it. Moving the machine is a job for a technician. |
| Air that cannot get through | Boxes or stock against the vents, or a clogged air filter on an air-cooled machine. | You, where the manual makes the air filter an owner job. |
| A dirty condenser | Dust or grease on the grille in front of it. | A technician. |
| Too little water, or warm water | A supply tap not fully open, a water filter past its change date, or a recent plumbing change. Warm water at the nearest cold tap. | The filter is changed as its manual says. Water pressure and the supply are for a plumber or a technician. |
| Scale or slime in the water system | Scale or slime on what you can see, and a clean that is overdue. See the guide to ice-machine cleaning and sanitising. | A technician on most machines. Check the manual for yours. |
| A setting that limits production | Some machines can be set to stop below full, or to make ice only at set times. Ask whether anyone has changed a setting. | A technician, or whoever set it. Leave the settings alone. |
| A fault inside the machine | None of the above, or a light or code on the front. | A technician. The refrigeration circuit and anything electrical inside the machine are not owner work. |
What lights or codes should you write down?
Lights, letters and codes belong to each maker and model. Some machines show a reminder to clean the air filter or to descale, some a water light when too little water reaches them, and some a notice for high temperature. Write down exactly what the display shows, or which light is on and whether it flashes, and when it appeared. Look it up in the manual for your model, and do not clear it or turn the machine off and on to make it go away: the technician needs to see it.
When should you stop using the ice?
Less ice is a nuisance. Ice that may not be safe is a food safety problem, and it is a separate question. Stop using the ice, empty it out and keep the machine's ice out of service if:
- the ice tastes or smells wrong
- there is mould or slime in the bin, at the chute or on the ice
- something has fallen into the bin, or anything is being stored in it
- your water supply is under a boil water advisory, because the machine makes its ice from that water
Then follow your food safety program. Your council's environmental health team registers most cafes, pubs and restaurants and is the place to ask about food safety, and the guide to ice-machine cleaning and sanitising covers a boil water advisory and putting the machine back into use.
What will the technician check?
We start with the water and the air, because a water problem can look like a refrigeration fault: the condenser, the air and water filters, the water supply and scale on the freezing surface. Then we time the cycles, weigh a harvest and compare the output with the maker's table at the room and water temperatures on the day.
We repair ice machines for hospitality venues. Have the log ready, with the brand, model and serial number from the plate on the machine, and the invoice or install date if you have them. Call ABL and read it out, or send it with an enquiry from the ice machines page.
Ice output log
Sources (19)
Checked on 20 November 2026
- Hoshizaki Australia: maintenance, 10 June 2025 (opens in a new tab)
- Hoshizaki: KM-40C-HC to KM-140C-HC ice makers, instruction manual (copy held by a reseller) (opens in a new tab)
- Hoshizaki Lancer: KM-40C-HC crescent cube ice maker specification sheet (opens in a new tab)
- Hoshizaki Lancer: KM-60C-HC crescent cube ice maker specification sheet (opens in a new tab)
- Hoshizaki Lancer: KM-140C-HC crescent cube ice maker specification sheet (opens in a new tab)
- Manitowoc: U65 undercounter ice machine installation, use and care manual, 2022 (copy held by a reseller) (opens in a new tab)
- Manitowoc: undercounter ice machines technician's handbook (copy held by a distributor) (opens in a new tab)
- Manitowoc: Indigo series QuietQube ice machines installation, use and care manual (copy held by a reseller) (opens in a new tab)
- Manitowoc: iT0500 50 Hz specification sheet (copy held by a reseller) (opens in a new tab)
- Scotsman: Prodigy Plus D series user manual, 2014 (opens in a new tab)
- Scotsman: Prodigy modular cuber technical service manual, 2015 (opens in a new tab)
- Moffat: Scotsman MXG M 327 modular ice maker specification sheet (copy held by a reseller) (opens in a new tab)
- Simag: SDE and SDH ice cube makers, use and ordinary maintenance, 2022 (copy held by a retailer) (opens in a new tab)
- AG Equipment: ICE95 ice machine manual (copy held by a reseller) (opens in a new tab)
- Pentair Everpure: slime reduction in ice machines (opens in a new tab)
- National Health and Medical Research Council: Australian Drinking Water Guidelines, guidance on boil water advisories (opens in a new tab)
- Safe Food Victoria: local council registered food businesses, what you need to know (opens in a new tab)
- Australian Government: Triple Zero (000) (opens in a new tab)
- ABL Refrigeration: commercial refrigeration services (opens in a new tab) ABL's own page.
Related pages
- Ice machine repairs and sales in Gippsland
Ice machine repairs, and the usual faults.
- Sizing a hospitality ice machine: production and storage
When the machine is working but the venue needs more.
- Ice-machine cleaning and sanitising: an owner maintenance plan
Who cleans and sanitises what, and when.
Want a technician to look at it?
Call ABL or send an enquiry. Have your notes ready: the brand, the model and what the unit is doing.
Filled in the record? Copy or print it first: it is not sent with a call or an enquiry.
