Commercial air conditioning maintenance agreements: questions to ask before you sign
Questions to ask before you sign a commercial air conditioning maintenance agreement: scope, visits, exclusions and reporting, with a comparison sheet.
Last updated
Before you sign a commercial air conditioning maintenance agreement, ask six things: which units it covers, what is done to each one at every visit, how often, what is left out, what you are told afterwards, and what happens when something fails between visits. Price comes last, because two agreements at the same price can cover very different work. The comparison sheet in this guide puts two proposals side by side.
How to use this guide
What does a maintenance agreement cover, and what does it not?
A proposal usually mixes three different things, and it helps to pull them apart.
| Part | What it is | What to check |
|---|---|---|
| Scheduled maintenance | Planned visits, with set tasks on each unit. | This is what the fee buys. It should be written out task by task. |
| Repairs | Putting right what a visit finds, or what fails between visits. | Usually extra. Look for how repairs are quoted and approved, and the rates. |
| Promises | Statements about how fast someone will attend, how few breakdowns there will be, or what the work does for health. | Ask for each one in writing, with what happens if it is not met. A promise that is only in the brochure is not in the agreement. |
Scheduled maintenance lowers the risk of a breakdown and finds problems early, while they are cheap to fix. It does not prevent every fault, and a proposal that says it will is offering something maintenance cannot deliver. Leaving a system until it fails is the most expensive way to run one over its life.
There is a duty behind it as well. WorkSafe Victoria's compliance code for workplace facilities (opens in a new tab) says heating and cooling facilities need to be serviced regularly and kept in proper working order. And the refrigerant handling code of practice (opens in a new tab) recommends that an owner without trained staff of their own has a routine maintenance agreement with a competent service technician or organisation.
Start with a list of what has to be covered
You cannot compare two proposals until both are pricing the same equipment. Make the list yourself and send the same one to each provider. For each unit, give its label or location, the brand and model, the type of system, the area it serves, its age, how many hours it runs, and anything awkward about reaching it.
Then add the parts that are easy to leave off: wall controllers, condensate pumps, zone motors and dampers, ducts and outlets, and any fan that brings outside air in or takes stale air out. An agreement that covers "all air conditioning on site" leaves you to argue later about what "all" meant. An agreement with the list attached does not.
The guide to commercial air conditioning asset registers covers how to build and keep the list.
What to compare between two proposals
| Compare | What a good proposal shows |
|---|---|
| Units covered | Every unit on your list, by name. Anything left out is stated, with the reason. |
| Tasks at each visit | A task list for each type of unit, taken from the maker's schedule for the model. "Service all units" is not a task list. |
| Visits a year | How many, and in which months. The guide to building a maintenance calendar covers how the number is set. |
| What changes the plan | The findings that bring a visit forward or add one: filters loading faster than expected, corrosion, a fault that repeats. |
| Exclusions | Written out. The usual ones are repairs, parts, refrigerant, calls outside working hours, hire of access equipment, and units that cannot be reached safely. |
| Parts and consumables | Which are in the fee, such as filters, and how everything else is priced and approved. |
| Reporting | A written report after every visit, unit by unit: what was done, what was found, readings and photos, and recommendations in order of urgency. |
| Access | Who supplies ladders and platforms, the hours of work, and what the provider needs from you on the day. |
| Who does the work | The licences held, the names of any subcontractors, and who signs the report. |
| Faults between visits | How to report one, what the agreement says about attendance, and the rates that apply. |
| Price and term | The fee for the year, whether it includes GST, how it changes, how long the agreement runs and how either side can end it. |
On licences: in Australia, work that involves handling a scheduled refrigerant needs a refrigerant handling licence (opens in a new tab), and a business that acquires, stores or disposes of refrigerant needs a refrigerant trading authorisation. You can check a licence at Look for the tick (opens in a new tab). Fixed electrical work on the equipment is for a licensed electrician (opens in a new tab).
Maintenance by the calendar, and by condition
The maker's schedule for each model is the floor. It lists the tasks and the base interval, and a proposal should not go below it. On top of that, a good agreement uses what each visit finds. If the filters on one unit are loaded at every visit, that unit gets seen more often. If a coil on the coast is corroding, it gets washed more often. If a unit in a clean office is spotless twice running, the extra visits can go elsewhere.
Ask each provider how findings change the plan, and who decides. Condition adds to the maker's schedule. It does not replace it.
How the scope differs by type of system
A proposal that gives every unit the same task list has not looked at what you have. Each type of system has something particular that the scope should name.
| System | What is particular to it | Ask the provider |
|---|---|---|
| Ducted | Most of the system is out of sight: the ducts, the dampers and zone motors, the outlets, the return air filter, and a sensor and controller for each zone. | Does the scope include the ducts, the zones and the controls, or only the two units? |
| Cassette | The unit sits in the ceiling of a room people use, and it lifts its condensate water out with a small built-in pump. | When will the work be done so the room can be cleared, and is the pump and its drain on the task list? |
| Multi-split | One outdoor unit serves several indoor units. Each indoor unit has its own filter, coil and drain, and a fault in the outdoor unit stops every room. | Is every indoor unit counted and visited, including the ones in rooms that are usually locked? |
| VRF | Many indoor units share one refrigerant circuit, run by controls and software specific to the maker. | Which brands of VRF system do you maintain, and do you have the training and the service tools for this one? |
| Rooftop packaged | The whole system is on the roof, in the weather. Coils and panels are exposed, and getting to the unit safely is part of the job. | How is the roof reached, who supplies safe access, and how often are the coils and panels cleaned? |
For a rooftop or coastal unit, ask about corrosion by name. Outdoor panels in a corrosive spot are washed on a shorter cycle than the rest of the system, and the proposal should say how often.
A practical agreement for a small office
A small office with two or three split systems does not need a thick contract. It needs the same answers on one page: the units, the tasks, the months of the visits, the fee, what a repair costs, and a report after each visit. One or two visits a year suits most small offices, with the filter cleaning between visits done by a named person where the manual for the model gives that job to the owner.
If a provider cannot put the scope for three units on a page, ask why.
Filters are not interchangeable
A filter is the part of the system that is handled most often, and it is where a cheap agreement saves money. A blocked filter cuts the airflow and makes the unit use more electricity to do the same work. A filter of the wrong size lets dust past its edges and onto the coil. A filter of a different type or grade from the one the unit was set up with changes the airflow through it.
So the agreement should name, for each unit, the size and type of its filter, whether it is washed or replaced, how often, and who supplies it. A change of filter type is something the provider agrees with you first, not a substitution made on the day.
Reading a cleaning proposal, and the health claims in it
A "deep clean" can mean a wipe of the casing or a full wash of every part that air and water touch. Before you compare prices, ask each provider to say:
- which parts are cleaned: filters, the indoor coil, the fan, the drain tray and the drain, the outdoor coil, the ducts and outlets
- how each is cleaned, and with what product
- how the room, the ceiling and the electrical parts of the unit are protected from water
- who does it, and what licence they hold
- what you get afterwards: before and after photos, and a note of anything found
- whether the clean is part of a service or instead of one
Coil cleaning is not a job for whoever is cheapest. Water is used next to electrical parts, and the wrong chemical damages the coil. It is work for a licensed technician.
Then look at what the proposal claims. A clean, well kept system is good practice. A claim that a clean or a treatment kills viruses, prevents illness or purifies the air for months is a different kind of statement, and it needs evidence. The Australian Competition and Consumer Commission says claims a business makes must be true and it must be able to prove them (opens in a new tab). Ask for the name of the product, what its own label says it does, and the evidence for the claim as it is worded in the proposal. If the answer is vague, treat the claim as sales copy and compare the proposals on the work.
Measures that do not hide repeat faults
If an agreement has performance measures, look at what they reward. A measure such as "jobs closed within two days" rewards closing jobs. A fault that is patched quickly, three times, scores better than one that is diagnosed properly once. And a system with a developing fault often compensates for it and keeps the rooms comfortable, so "no complaints" can hide a problem as well.
| Measure | What it shows |
|---|---|
| Visits done in the month they were due | Whether the plan is being kept. |
| Reports received within a set number of days | Whether you are being told what was found. |
| Repeat faults on the same unit | Whether faults are being fixed or patched. Count a second call for the same fault within a year, and ask for the cause. |
| Recommendations still open | Whether findings are being acted on, by them or by you. |
| Breakdowns between visits, unit by unit | Which units the plan is not working for. |
Two or three measures are enough. A unit that keeps turning up in the repeat column is a candidate for the guide to repairing or replacing a commercial air conditioning system.
Access: secure sites, fixed furniture and subcontractors
A secure site
Maintenance should fit your site controls, not get around them. Agree in advance who is coming, by name, and what they need to show at the door. Settle which rooms they are escorted in, who holds the keys and alarm codes, how they sign in and out, and any check your site requires of visitors. Agree the induction once and record it, so it is not repeated or skipped at each visit. WorkSafe Victoria's information on engaging a contractor (opens in a new tab) sets out the health and safety duties an employer has to contractors on its site, and the duties contractors have in return.
Indoor units above fixed furniture
An indoor unit above a reception counter, a bed, fixed shelving or a machine is the one that gets skipped. A ladder cannot stand where it needs to, so the unit is either missed at every visit or reached in a way nobody should. Solve it once. Move the furniture, move the unit, provide a platform that suits, or fix a time when the area can be cleared. Write the method into the agreement, and require any unit that could not be reached to be listed in the report as not serviced.
When part of the work is subcontracted
The business you sign with may bring in others for access equipment, electrical work, controls or duct cleaning. That is normal. What matters is that you know who they are. Ask which parts of the work are subcontracted and to whom, what licence each holds, who signs the report for their part, and who you call when something they worked on goes wrong. The answer to the last question should be the business you signed with.
Air conditioning and ventilation: who maintains what
Heating and cooling are one job and ventilation is another, and they are often maintained by different contractors. The gaps fall between them: an outside air fan that the air conditioning contractor takes to be someone else's, a toilet or kitchen exhaust fan that is on nobody's list, a filter on a fresh air intake that has not been changed since it was fitted.
List every fan and every intake in the building, and write beside each one who maintains it. Where a system is one of the building's essential safety measures (opens in a new tab), such as an air handling system used to manage smoke, the Building and Plumbing Commission says the owner must see that it is maintained and keep the records, so that work usually sits in its own contract. The guide to air conditioning and outdoor air ventilation explains why the two are separate.
Maintenance agreement comparison sheet
Asking ABL for a proposal
ABL services and repairs air conditioning for businesses in Bairnsdale and East Gippsland. Send us your list of units and the points on this page, and ask us the same questions you ask anyone else. Our air conditioner servicing page covers what a service involves, and the enquiry form is on our air conditioning services page.
For the work that needs a closed building, see the guide to planning maintenance for an annual shutdown.
Sources (14)
- NSW Government: I am your optimisation guide, heating, ventilation and air conditioning systems, 2015 (opens in a new tab) Checked on 19 November 2026.
- WorkSafe Victoria: compliance code, Workplace facilities and the working environment, December 2023 (opens in a new tab) Checked on 19 November 2026.
- Australia and New Zealand refrigerant handling code of practice, part 2, 2025 edition (opens in a new tab) Checked on 19 November 2026.
- Australian Refrigeration Council: frequently asked questions (opens in a new tab) Checked on 17 November 2026.
- Australian Refrigeration Council: Look for the tick (opens in a new tab) Checked on 17 November 2026.
- Energy Safe Victoria: electrical licence types, reviewed 1 July 2026 (opens in a new tab) Checked on 17 November 2026.
- ActronAir: installation and commissioning guide, variable capacity commercial ducted indoor unit, version 4 (opens in a new tab) Checked on 19 November 2026.
- ActronAir: installation and commissioning guide, commercial split ducted outdoor unit, version 8 (opens in a new tab) Checked on 19 November 2026.
- Daikin: maintenance tips (opens in a new tab) Checked on 19 November 2026.
- Panasonic Australia: commercial air conditioning range (opens in a new tab) Checked on 19 November 2026.
- Australian Competition and Consumer Commission: false or misleading claims (opens in a new tab) Checked on 17 November 2026.
- WorkSafe Victoria: information on engaging a contractor, reviewed 28 July 2022 (opens in a new tab) Checked on 19 November 2026.
- Building and Plumbing Commission: essential safety measures (opens in a new tab) Checked on 19 November 2026.
- ABL Refrigeration: air conditioning services (opens in a new tab) ABL's own page. Checked on 19 November 2026.
Related pages
- Business air conditioning pre-summer maintenance calendar
How the number and timing of visits is set for each unit.
- Annual shutdown HVAC maintenance planning for a business
The maintenance to save for a closed period.
- Commercial AC asset registers and the records to retain
How to build the list of units an agreement is priced from.
Comparing maintenance proposals?
Send ABL your list of units with an enquiry, or call and ask us the same questions.
Filled in the record? Copy or print it first: it is not sent with a call or an enquiry.
