Skip to the content

Comparing commercial refrigeration quotes that include different things

How to line up commercial refrigeration quotes: equipment, site work, commissioning, warranty and exclusions, with a workbook to price what each leaves out.

Last updated

Before you compare the totals, put each quote into the same lines: equipment, delivery and access, building and electrical work, refrigeration installation, controls, commissioning and documents, warranty, and exclusions. A cheaper total may leave out work the other quote includes, and that work comes back as a separate bill. Put a figure on each gap, add it to the quote that left it out, and then compare.

How to use this guide

  1. Step 1: Split the quotes

    Sort every item into the same lines for each quote.

    Go to Quote lines
  2. Step 2: Price the gaps

    Find what each one leaves out or leaves to others.

    Go to Exclusions
  3. Step 3: Fill in the workbook

    Two quotes side by side, with the gaps priced.

    Go to the record

Split each quote into the same lines

Ask each supplier for a written quote against the same requirements, and make sure you know exactly what each one covers. Then sort every item into these lines. A line a quote does not mention is a question to ask, not a saving.

The lines to split every refrigeration quote into
LineWhat it should state
EquipmentEach model number and quantity, its temperature class and duty, its tested energy use and its refrigerant. The guides to climate classes and energy ratings show what to check. Watch for "or equivalent", which lets a different model in.
Delivery and accessFreight and packing, whether delivery stops at the kerb or the item is put in position, who unloads, stairs or tight doorways, packaging removal, and taking the old equipment away.
Building workFloors, insulated floor panels for a freezer room, ramps, penetrations through walls and ceilings, sealing, and making good afterwards.
Electrical workA dedicated power point for a plug-in cabinet, or a circuit and isolator for a hard-wired unit, three-phase supply where needed, and any door heater or alarm wiring.
DrainageWhere the condensate drain runs and what it connects to, and who makes the connection.
Refrigeration installationFor a remote cabinet or a coolroom: the refrigerant pipework, the refrigerant, the condensing unit's mounting, and the licensed technician who installs and commissions it.
Controls and monitoringThe controller and its settings, alarms, and any temperature monitoring with its subscription.
Commissioning and documentsThe test run to temperature, the commissioning record, the manuals, and for a larger system the logbook.
WarrantyThe maker's warranty on the equipment and the installer's on the work, with their lengths and conditions.
Exclusions and assumptionsEverything marked "by others", "supply only" or "not included", provisional sums, after-hours work, and how changes will be priced.

Exclusions that change the total

These are the exclusions that most often separate two totals. Each one is a real cost on the day, whoever carries it.

  • Freight and delivery. Equipment prices commonly leave out transport, packing and insurance unless the quote includes them. Unloading is often the buyer's job unless agreed in writing.
  • Installation and commissioning. A supply-only quote is for the goods. Installing and commissioning them is extra unless it is written in.
  • Other trades. Work by builders, electricians and plumbers, and changes to the premises, are commonly excluded and left to you to arrange.
  • Electrical work. In Victoria, electrical installation work is done through a registered electrical contractor, whose licensed electrician gives you a Certificate of Electrical Safety (opens in a new tab) for it. A refrigeration quote that says "power by others" has left that job to you.
  • Provisional sums and prime cost items. A provisional sum is an estimate for work that cannot be priced yet, and a prime cost item is an allowance for something not yet chosen. Both can move. Ask for a fixed price where you can, or the basis of the estimate where you cannot.
  • Changes. Agree how a change will be priced before work starts, and put each change in writing.

Price each gap with a quote from the trade that would do it, or ask the supplier to include it. Then compare complete jobs, not totals.

Supply only or a complete installation?

What remains to be arranged after a supply-only purchase depends on the equipment.

What a supply-only purchase leaves for you to arrange
EquipmentWhat still has to happen
A plug-in cabinet with its own refrigerationNo work on the refrigerant circuit is needed on site, so installing it is normally the buyer's job, following the maker's instructions: delivery into position, levelling, the clearances the manual asks for, its own power point, and a run to temperature before loading. A new power point is electrical work.
A remote cabinet, or a coolroom with a split systemThe refrigerant pipework, the condensing unit and the commissioning are refrigeration work. Where the system uses a scheduled refrigerant, which includes the HFCs, that work needs a technician with a refrigerant handling licence, whether or not refrigerant is in the system yet. A supply-only price is not the price of a working system.

You can check a refrigeration technician's or business's licence at Look for the tick (opens in a new tab). Businesses that hold a Refrigerant Trading Authorisation, and some licence holders, must show their permit number on their quotes, so look for it there.

Weighing a flat-pack coolroom kit proposal

A coolroom kit is a set of insulated panels and a door that lock together, with their fittings. What else is in the box differs from maker to maker, so check each of these before you compare a kit price with an installed room.

  • The refrigeration. Some kits are panels only. Others include the refrigeration, as a split system or as a one-piece unit. A split system has to be installed and commissioned by a licensed refrigeration technician, as for a remote cabinet above. A one-piece unit arrives charged with refrigerant, with no pipes to run on site, but it still has to be mounted, drained and connected to power. Ask which kind the kit has and whether that work is in the price.
  • The floor. Some coolroom kits leave the floor out for an indoor room on a level floor, and some include it. A freezer room needs an insulated floor.
  • Freezer room parts. A freezer room door needs a heater in its frame, and the room needs a pressure relief port. Both are wired in by a licensed electrician.
  • The size. Check whether a size is external or internal: the room inside is smaller by two panel thicknesses each way. Check the clearance the maker asks for above and around the room.
  • Extras. Shelving, ramps and door upgrades are commonly sold separately.
  • Getting it in. Panels are long, so check how the kit is delivered and who unloads it.
  • Two warranties. The maker's covers the kit, and the installer's covers the installation.

A room a person can walk into also has door, lighting and alarm requirements in clause G1D3 of the National Construction Code 2025 (opens in a new tab), which Victoria adopted on 1 May 2026. Our coolroom and freezer room installation page lists them. Ask which of them the kit includes and who fits and wires them. Your building surveyor decides how the code applies to your room.

Refrigeration in a fitout tender with several contractors

In a fitout, the refrigeration contractor's work meets the builder's, the electrician's and the plumber's. Each interface needs one name against it, or it falls between quotes. Agree these before the tender closes:

  • Power: who runs the supply to each isolator and power point, and who connects the equipment.
  • Drains: who runs each condensate drain, and who connects it to a tundish or the building's drainage.
  • Floors and slabs: who sets down the floor for a freezer room, and who builds any plinth.
  • Penetrations and sealing: who cuts and seals the holes for pipework and cables through walls, ceilings and coolroom panels.
  • Plant positions: who provides the mounting, access and airflow for the condensing units.
  • Coolroom safety items: who supplies and wires the inside-opening door hardware, the lights, the indicator lamp and the alarm.
  • Monitoring: who connects any monitoring to the site's network or power.
  • Commissioning: when it happens, who witnesses it, and who receives the records.

Where a quote says "by others", the tender should say which other contractor, and that contractor's quote should include it.

Warranty questions to ask before you buy

Commercial equipment warranties differ widely between makers and ranges, from 1 year to 5 in current Australian terms. Read the terms, not the headline. Ask the supplier:

  • How long does it run, and does it cover parts and labour, or parts only? A remote cabinet can carry a shorter, parts-only warranty.
  • Does it need registering, and does registering change the length?
  • What has to be done to keep it: condenser cleaning, servicing, ventilation, a maximum room temperature?
  • What is excluded? Door seals, glass and lights are commonly treated as consumables.
  • Is warranty labour free at your site, or only within a set distance or travel time of an authorised service agent? This matters in East Gippsland.
  • Are after-hours call-outs charged?
  • Does it cover only the first user at the first site?
  • Who warrants the installation, for how long, and what is in writing?

A maker's warranty is on top of the consumer guarantees, not instead of them. A business is covered by the consumer guarantees (opens in a new tab) when what it buys costs less than $100,000 including GST, or is the kind of thing commonly bought for household use. They do not cover goods bought to resell, to use or transform in production or manufacturing, or to repair or treat other goods. That is as at November 2026. Makers' warranties generally exclude stock lost in a breakdown, and one maker's terms put insuring it on the buyer from delivery, so plan for a failure.

Buying used commercial refrigeration

A used cabinet can be good value, but a quote for one needs more checking than a quote for new.

  • Who is selling. Second-hand goods sold by a business are still covered by the consumer guarantees, with their age, price and condition taken into account. A private sale by someone not in business carries few of them. Calling it "as is" does not take those rights away, but you have no claim for a fault you should have seen when you inspected it.
  • The plate. The rating plate shows the model, the serial number, the power supply and the refrigerant. The year of manufacture may be coded into the serial number: ask the seller or the maker to read it.
  • The refrigerant. Equipment on R22 can still be serviced, but R22 imports stop entirely on 1 January 2030, after which servicing relies on recycled gas and parts can get harder to find. Equipment on an HFC refrigerant is not affected by the HFC phase-down, which limits imports of bulk gas.
  • Energy. A used cabinet is outside the supply rules for energy, so it may have been built to an older, less efficient standard.
  • Warranty. A maker's warranty usually covers the first user only.
  • Records. Ask for the service history and, for a larger system, the logbook. Repeated refrigerant top-ups in it point to a leak.
  • A test run. Run it to temperature and check the food or a probe reading, not only the display: see the guide to food temperature and fridge readings.

Checking the refrigeration before you buy a food business

A food business registration does not pass to a buyer: the new owner applies for their own. East Gippsland Shire Council's steps are to contact its Environmental Health unit, request an inspection and information on the registered premises, and apply to register seven days before settlement (opens in a new tab). Councils recommend a pre-purchase inspection, but it reports on Food Act items, not on how well the equipment works. For a licensed meat, poultry or seafood business, Safe Food Victoria (opens in a new tab) says the licence cannot pass to a new owner, who applies for a new one. A dairy farm licence may transfer.

The condition of the refrigeration is a separate check, and failing equipment is a cost you take on with the business. Before settlement, list every coolroom, freezer and cabinet with its age, refrigerant, service history and any logbook, and have a refrigeration technician look at each one and say what it needs. Work in the business before settlement if you can, so you see the equipment run through a busy day.

Our commercial refrigeration maintenance page sets out what a service visit checks. To weigh what you find, see the guide to comparing repair cost with energy and stock-loss risk.

Quote comparison workbook

Refrigeration quote comparison

Fill in a part for each quote, then the gaps. Copy it or print it.

Your answers stay on this open page. They are not saved or sent. Copy or print them before you leave.

Quote A

Quote A: delivered into position
Quote A: installation and commissioning included
Quote A: commissioning record and manuals included

Quote B

Quote B: delivered into position
Quote B: installation and commissioning included
Quote B: commissioning record and manuals included

The comparison

Who to call

We supply, install and service commercial refrigeration, coolrooms and freezer rooms for businesses in Bairnsdale and East Gippsland. Our commercial refrigeration equipment supply page explains how to ask for a quote. Send the workbook with your enquiry, or call and talk it through. If monitoring is part of the job, see the guide to choosing commercial refrigeration temperature monitoring.

Sources (35)

Holding quotes that do not line up?

Send ABL your quote comparison with an enquiry, or call and talk it through.

Filled in the record? Copy or print it first: it is not sent with a call or an enquiry.