Commercial refrigeration maintenance checklist: set the schedule by duty and risk
Work out how often each coolroom, freezer room and commercial fridge needs servicing from its duty and the cost of a failure, with a worksheet to agree it.
Last updated
Set how often each coolroom, freezer room and commercial fridge is serviced from two questions: how hard does it work, and what would a failure cost you? Start from the tasks and the interval in the manual for each unit. Then add checks, or shorten the interval, where a unit runs long hours, sits in dust, kitchen grease or salt air, has failed before, or holds stock that is hard to replace and has nowhere else to go. One fixed interval for every unit, such as every three months, will be too long for some and more than others need. Split the checklist into the care your own staff may give and the work that needs a technician, write the evidence down for each unit, and agree the schedule from it.
How to use this guide
Step 1: Check what changes the schedule
Go through the table for each unit: its duty, its site, its history and its stock.
Go to Schedule factorsStep 2: Fill in the worksheet
One for each unit, with its manual and the last service reports beside you.
Go to the recordStep 3: Call to agree it
Talk the worksheets through with us, or send them with an enquiry.
Call (03) 5153 2650
How do duty and the cost of a failure set the schedule?
Rate each unit on two things. The first is how likely a problem is, which comes from how hard the unit works and where it sits. The second is what happens when it stops: can the business carry on without it, how much stock is at risk, and is there somewhere else to put that stock? Refrigeration can be critical to a business because of what it holds. Its type, its size and how much refrigerant it holds also change the intervals that suit it.
| What you find | What it usually means for the schedule |
|---|---|
| Short hours, a clean site, and a failure you can absorb | The tasks and interval in the manual, with your staff checks between visits. |
| Long hours or a harsh site, and a failure you can absorb | Shorter intervals for the parts the site wears, such as inspecting and cleaning the condenser. |
| Short hours, a clean site, but a costly failure | The interval in the manual, plus temperature monitoring with an alarm and a written plan for the stock, so a fault is found early. |
| Long hours or a harsh site, and a costly failure | The most attention: shorter intervals, monitoring with an alarm, and a backup plan agreed before it is needed. |
Write down what would actually happen if the unit stopped for a day. A second fridge or coolroom that can take the stock lowers the cost of a failure, and so does an alarm that reaches someone who can act. The temperature monitoring page covers alarms.
What changes the schedule for a unit?
These are the things that move a unit away from the starting point in its manual. Each row says what to look for on your site and what to ask for.
| On your site | Why it matters | What to ask for |
|---|---|---|
| Long hours, or running around the clock | More running hours and more door openings put more load on the plant, and leave less time when it can be off. | Visits at your quietest time, and a list of the work that needs the unit off. |
| A dusty plant area | Dust clogs the condenser coil, so the plant works harder to hold temperature and can break down. | The condenser looked at more often, and how dirty it was written on each report, so the interval follows what is found. |
| Kitchen grease near a condenser | Airborne grease sticks to the coil and acts like an insulator. The compressor works harder and can fail, and grease needs a cleaner made to break it down. | A technician to assess the coil and set the cleaning method and interval from what they find. |
| Coastal salt air | Salt air speeds up corrosion of air-cooled condensers, pipework, fixings and casings. Corrosive air calls for equipment designed for it. | Corrosion recorded at each visit: where it is, how far it has gone and whether it is spreading. Coated or corrosion-resistant parts still need inspecting. When a part is replaced, ask what suits the site. |
| Building works nearby, or a new fitout | Building dust settles on coils, and a fitout can put a heat source, a wall or stored goods where the plant draws its air. | A check once the works finish, ahead of the next scheduled visit. |
| More storage around the plant as the business grows | Boxes and shelving pushed against a unit stop it shedding heat, and take the space a technician needs to work. | A clear zone kept around each unit, and any access problem written on the visit report. |
| An isolated site | Travel is part of every visit and every breakdown call, and there may be nobody on site when a fault starts. An alarm only reaches anyone while its connection is working. | Monitoring with an alarm that reaches someone who can act, a written plan for the stock, and access details agreed before they are needed. |
| Faults in the last year | A part that has failed, or a fault that keeps coming back, shows where to look first. | The next visit to check that part, and the report to say what was found. For faults that come and go, see the guide to recording intermittent commercial refrigeration faults. |
| Stock that is hard to replace, with no backup | The cost of a failure is high even when the unit works lightly. | Monitoring with an alarm, and a written plan for where the stock goes. |
| The manual for the unit | It sets the maintenance tasks and the preventive maintenance schedule for that model. Under the refrigerant handling code of practice (opens in a new tab), preventive maintenance follows the instruction manual. | Every task in the manual on the schedule, at least as often as the manual says. |
| What the visits find | Condition is the evidence. There is no general rule for how often a coil needs cleaning, so what each visit finds shows whether the interval fits the site. | The condition of the coils, the door seals and the drain on every report, so the schedule can be reviewed against it. |
Who does what: your staff or a technician?
Your staff see the equipment every day, so their checks catch changes between visits. Their part is to look, keep things clear, clean what the manual gives them, record and report. Work inside the equipment, on its refrigerant circuit or on its wiring is for a technician or an electrician. Where the manual for your model says something different, follow the manual. For the cleaning itself, see the guide to cleaning commercial refrigeration.
| Part or task | Your staff | A technician or electrician |
|---|---|---|
| Door seals, hinges and closers | Look along all four sides of each seal for gaps, tears or ice. See that the door closes and seals on its own, and record what you find. | We replace a worn seal and repair hinges, closers and door heaters. |
| Condenser | Keep the air path clear and look at the coil once a week. Leave cleaning to the technician unless the manual for your model makes it your job. | We clean the coil and the fans, and set how often that needs doing for your site. |
| Evaporator, drain and ice | Look for ice building up on the coil and for water on the floor or in the cabinet, and report it. Do not chip or scrape ice off. | We clean the coil, clear the drain, and check the heaters and the defrost. |
| Defrost | Note when defrosts run, how long they last and what the display shows after them. | We change defrost times and settings where the controller allows. |
| Temperatures, controls and alarms | Probe the food, keep the temperature record, and write down any alarm or code before it clears. Leave set points and alarm limits alone. | We change set points and alarm limits, and check that sensors read correctly. |
| Wireless temperature sensors | Note when each battery is due. Change a battery only where the system's guide makes it a user job, one sensor at a time, and confirm that sensor is reporting again before you move to the next. | Faulty sensors, lost connections and alarm settings go to the monitoring supplier or your technician. |
| Lights | Report a light that has failed or broken. | Some cabinets have lights that the owner cannot service. Fixed lighting in a coldroom is electrical work for a licensed electrician. |
| Castors and cabinet position | Keep the castor brakes on once a cabinet is in place, and release them before moving it. Move only a cabinet made to roll, across a level floor, with a cord long enough to reach. | We move or re-level a cabinet that is piped to remote plant or fixed in place, and check that it drains. |
| Refrigerant circuit | Report oil marks on pipework, or a unit that runs most of the time without getting cold. | Work that involves handling a scheduled refrigerant, or a part of the equipment that could release one, needs a refrigerant handling licence (opens in a new tab). |
| Power supply and wiring | Report a damaged power cord or plug. | Fixed electrical installation work in Victoria requires a licensed electrician (Energy Safe Victoria (opens in a new tab)). A damaged power cord is replaced by a service agent or a similarly qualified person. |
| Plant area and access | Keep the area around each unit clear of stock, rubbish and stored goods, and have keys and access ready for each visit. | Ask for anything that blocks air or access to go on the visit report. |
| How often | What your staff check |
|---|---|
| Each trading day | Probe the food, fill in the temperature record, and write down any alarm or code before it clears. A category one food business makes its records each day it does a prescribed activity, as FSANZ (opens in a new tab) sets out. |
| Each week | Look at the condensing unit: how it is running, and the state of the condenser coil. Look only, and report a dirty coil or a change. |
| Each month | Check every door seal the same way, as the door seal checks below set out. Give the condenser a light brush only where the manual for your model makes that a staff job. |
How often a technician comes, and what they do, comes from the manual for each unit and the worksheet on this page.
Teaching new staff what to report
Give every new starter the same short routine on their first shifts, and go over it again when equipment changes.
- Who to tell. One named person on each shift, and the number to call when they are not there.
- What to write down. Which unit, the time, the reading on the display, a probe reading of the food, any alarm or code, and what they saw or heard. Some alarms clear themselves, so the note comes first.
- What not to do. Do not take off panels, change settings, chip ice, or keep restarting a unit to clear a fault.
- When to call straight away. Use the warning signs on the coolroom and commercial fridge repairs page.
Door seal checks that tell you something
A seal check is only useful if it is done the same way each time. Pick a day each month, check every door, and write down the same things, so a change shows up.
- The door, and the date.
- Any tear, split or flattened section, and where it is.
- Any gap, or frost or ice along the seal.
- Whether the door closes and seals by itself.
- Whether the seal was cleaned.
Call us when a seal is torn or cracked, when a gap or frost comes back after cleaning, or when a door no longer closes on its own.
Which maintenance needs an outage?
Much of a routine visit is done with the equipment running. Cleaning a coil, and work on the refrigerant circuit or the wiring, need it off. Ask which tasks on your scope need an outage and for how long, and plan the stock before the day.
| Work | The unit during the work | Plan for the stock |
|---|---|---|
| Looking: staff checks and the technician's inspection | Running as normal. An in-service leak inspection is done with the system running. | No change. |
| Cleaning the condenser coil | Off at its power supply while the coil is cleaned. | Keep the doors shut while it is off, and ask how long it will be. |
| Cleaning the evaporator coil or the drain | Out of operation, with its power off, while the work is done inside the room or cabinet. | Move or cover food near the work, and plan where chilled stock goes if the unit will be off for long. |
| Checking a defrost | Running a defrost while the technician watches, so the air inside warms for a while. | Choose a time away from deliveries and your busiest hours. |
| Repairs to the refrigerant circuit, the compressor or the fans | Off for the length of the repair. A leak is repaired before the system is recharged. | Move potentially hazardous food to another cold space, and hold deliveries until it is running again. |
| Electrical work, such as a new coldroom light | Done by a licensed electrician. Ask what will be off, and for how long. | Cover or move open food below the work. |
Where you have two units, have them done one at a time. For a long job with nowhere to put the stock, ask about coolroom hire for the dates, and see the guide to a commercial refrigeration contingency plan for where else stock can go.
Freezer defrosts and your trading day
Freezer rooms and freezers run their defrosts on their own. Depending on the controller, a defrost starts at set clock times or after a set interval. A defrost that falls during deliveries or your busiest hours adds door openings and warm air at the wrong moment. A technician can often move it, but needs to know what happens now. For a week, note:
- the time each defrost starts and how long it lasts, if the display shows a defrost symbol or message
- what the display reads during and after it: some controllers hold the reading from before the defrost, so probe the food as well
- whether it falls during deliveries, cleaning or service
- any alarm that comes up just after a defrost
- ice building up on the coil between defrosts, or water or ice left in the room afterwards.
Leave the defrost settings to the technician. Defrosting more often than needed makes the equipment work harder, and too little lets ice build on the coil.
Replacing coldroom lighting
Plan lighting work around the cold, the damp and the food. Fixed lighting is electrical work for a licensed electrician, and unqualified electrical work is illegal (Energy Safe Victoria (opens in a new tab)). Ask for:
- a fitting made for the room's temperature and for damp and washdown, with the maker's rating checked against the room
- a shatter-proof globe, a protective sleeve or a cover, so a broken lamp cannot drop glass onto food
- enough light for staff to see that the room is clean and to read labels and thermometers
- every hole through a panel for the fitting, its supports or its cable sealed against vapour
- LED fittings where possible, with lights off when nobody is in the room, because lights add heat to it
- a time when open food can be moved or covered below the work.
Planning around peaks: harvest, milking and hot weather
Book preventive work before the period when your cold storage matters most, not during it. A failure at the peak puts the most stock at risk.
Before the harvest
Have the coolroom serviced before the harvest starts, while it is empty or lightly loaded. Produce arriving with field heat in it puts the biggest load on the room, so a fault then costs the most. Tell us your expected harvest dates, how much produce comes in a day and how it is cooled before storage. For loading the room during the peak, see the guide to planning cold-storage loading during a harvest peak.
Between milkings
The vat's refrigeration has to cool the milk from every milking, so planned work fits the window after one milking's milk has cooled and before the next starts, or after the tanker has collected. Tell us your milking times and collection days. Cooling is under the most pressure at peak milk production and in the hottest weeks, so look at how the vat cools then, record it, and book a service before those periods. A refrigeration unit that is still running most of the time once the milk is cold is a reason to call. Vat refrigeration is serviced by a qualified refrigeration technician: see farm and dairy refrigeration.
Before forecast extreme heat
Check each unit's known limits before the heat arrives:
- The cabinet's climate class. It is on the label, and it gives the hottest room the cabinet is made for: 40°C for class 5. See the guide to commercial fridge climate classes.
- The condensing unit's limits. Its manual gives the conditions it is designed for. A unit starved of cool air runs at higher pressures, works poorly and can fail.
- Clear air around the plant. Nothing stacked against it, and hot air from its outlet not drawn back in.
- A clean condenser. Book the cleaning ahead of the heat rather than in the middle of it.
- Fewer door openings and no warm stock. Door openings add far more load in hot weather, and hot food or overstocking cuts what a fridge can cool.
- A plan for the stock if a unit cannot keep up. See the guide to a commercial refrigeration contingency plan.
What should a service contract or facilities scope cover?
A contract that says "quarterly service" tells you little. Check it against the maker's instructions for each unit and against what a failure would cost you. A scope that only says "in accordance with DA19", AIRAH's maintenance manual (opens in a new tab), is not enough on its own either: the manual leaves the scope and the level of maintenance for each unit to be decided.
| Check | What it should say |
|---|---|
| Every unit is listed | Each coolroom, freezer room, cabinet and vat, by brand, model and location, matching what is on site. |
| The maker's tasks are covered | Each task in the manual for each unit, at least as often as the manual sets. |
| The level suits the unit | More attention for the units the business depends on, rather than one level for everything. |
| Staff tasks are written down | What your staff do between visits, from the task split on this page. |
| Outages are planned | Which tasks need a unit off, when that can happen and who moves the stock. |
| Each visit is recorded | A written report after each visit, and the logbook kept up to date where a system holds more than 3 kg of refrigerant. The commercial refrigeration maintenance page covers what a visit record holds. |
| Licensed work is named | Refrigerant work by a licensed refrigeration technician, and fixed electrical work by a licensed electrician. |
| Faults between visits | How staff report a fault and who they call, out of hours as well. |
| The schedule is reviewed | A date to review the schedule against what the visits have found. |
For a facilities tender, set out the outcome as well as the tasks: the temperature each unit has to hold, how alarms are answered, and the records you need back. Then compare tenders on what they cover, not on price alone.
Scheduling worksheet
Agreeing the schedule with ABL
Send a worksheet for each unit with an enquiry, or have them in front of you when you call. We agree the schedule with you from the manuals, your site and what a failure would cost, and the visit reports then show whether it fits. What a visit includes and the usual intervals are on the commercial refrigeration maintenance page. If something has already failed, go to the coolroom and commercial fridge repairs page.
Sources (45)
Checked on 19 November 2026
- ABL Refrigeration: commercial refrigeration services (opens in a new tab) ABL's own page.
- Australia and New Zealand refrigerant handling code of practice, part 2, systems other than self-contained low charge systems, 2025 edition (opens in a new tab)
- Australian Refrigeration Council: frequently asked questions (opens in a new tab)
- AIRAH: DA19 HVAC&R Maintenance (opens in a new tab)
- AIRAH and ARBS: DA19 user guide, specifying a maintenance package with DA19, 2019 (opens in a new tab)
- Business Victoria: optimise performance of your commercial refrigeration and cooling systems, 2022 (opens in a new tab)
- Australian Government, energy.gov.au: refrigeration guide for businesses (opens in a new tab)
- Food Standards Australia New Zealand: Safe Food Australia, chapter 3.2.2, file revised April 2026 (opens in a new tab)
- Food Standards Australia New Zealand: Safe Food Australia, chapter 3.2.3, food premises and equipment (opens in a new tab)
- Food Standards Australia New Zealand: thermometers, updated 1 October 2025 (opens in a new tab)
- Food Standards Australia New Zealand: evidence tool, updated 1 October 2025 (opens in a new tab)
- Food Standards Australia New Zealand: temperature control for horticulture, updated 1 October 2025 (opens in a new tab)
- Federal Register of Legislation: Greenhouse and Energy Minimum Standards (Refrigerated Cabinets) Determination 2024 (opens in a new tab)
- Energy Safe Victoria: electrical licence types, reviewed 1 July 2026 (opens in a new tab)
- Energy Safe Victoria: electrical DDIY, don't do it yourself (opens in a new tab)
- SA Health: power failures and food safety requirements for businesses (opens in a new tab)
- SafeWork SA: cold storage facilities (opens in a new tab)
- South Gippsland Shire Council: food business fit out guide, 2024 (opens in a new tab)
- AIRAH: skills workshop 131, insulated enclosures in coldrooms, May 2020 (opens in a new tab)
- NSW Office of Environment and Heritage: industrial refrigeration guide, 2017 (opens in a new tab)
- Heatcraft: installation and operations manual for condensing units, H-IM-CU, September 2026 (opens in a new tab)
- Danfoss: Optyma Plus condensing unit instructions, 2022 (opens in a new tab)
- Danfoss: Optyma Cooler unit cooler installation and maintenance instructions, 2021 (opens in a new tab)
- Danfoss: cold room troubleshooting and fault diagnosis (opens in a new tab)
- Danfoss: cold room setup by application (opens in a new tab)
- Daikin: monoblock refrigeration unit explained (opens in a new tab)
- Foodservice Equipment Reports: clean that condenser, 2017 (opens in a new tab)
- SKOPE: user manual for the SC430N upright glass door fridge, February 2022 (opens in a new tab)
- Williams Refrigeration Australia: operator and user manual, April 2020 (opens in a new tab)
- Norlake: tips for troubleshooting and maintaining your walk-in, updated 8 June 2026 (opens in a new tab)
- Norlake: walk-in installation manual, March 2018 (opens in a new tab)
- Hussmann: Innovator RIM door system installation and operation manual, February 2021 (opens in a new tab)
- Hillphoenix: self-contained or remote display case, 2023 (opens in a new tab)
- Glamox: lighting for cold and freezer rooms (opens in a new tab)
- CAREL: ir33 platform controller user manual, 2010 (opens in a new tab)
- Dixell: XR06CX controller instruction manual, 2015 (opens in a new tab)
- Clever Logger: I got a low battery alarm, updated 23 October 2026 (opens in a new tab)
- Clever Logger: I changed the battery and the alarm didn't go away, updated 17 November 2025 (opens in a new tab)
- Clever Logger: troubleshooting offline gateways, updated 17 November 2025 (opens in a new tab)
- Testo: Saveris 2 Wi-Fi data logger system, instruction manual (copy held by a distributor) (opens in a new tab)
- Postharvest management of vegetables (Hort Innovation): cool rooms (opens in a new tab)
- Tree Fruit: maintaining fruit quality in storage, January 2018 (opens in a new tab)
- Dairy Australia: milk cooling and collection (opens in a new tab)
- Fonterra Farm Source: understanding your milk cooling system, 2023 to 2024 (opens in a new tab)
- Fonterra Farm Source: assessing your current milk cooling performance (opens in a new tab)
Related pages
- Commercial refrigeration maintenance in Gippsland
What a visit covers, the usual intervals and how to book.
- Cleaning commercial refrigeration: operator tasks and limits
The cleaning your own staff do, and where it stops.
- A commercial refrigeration contingency plan
Where the stock goes when a unit is off.
Want a schedule that fits your equipment?
Send ABL a worksheet for each unit with an enquiry, or call and talk it through.
Filled in the record? Copy or print it first: it is not sent with a call or an enquiry.
