Skip to the content

Choosing a refrigerated prep counter for your menu and service

How to match a refrigerated prep counter to your ingredients, pans, worktop and busy service, what to ask the supplier, and a specification to fill in.

Last updated

Choose a refrigerated prep counter from your menu and your busiest hour, not from a catalogue. For each ingredient, note the pan size and depth it needs and how much reserve has to sit below it. Note how often the lids, doors and drawers open, how much worktop the job takes, and whether customers will see or reach the food. Then ask the supplier for the model's limits: the room temperature it is rated for, the pans and depths it takes, its load limits, when its lid has to be closed and how it has to be cleaned.

How to use this guide

  1. Step 1: Map your ingredients

    Each one to a pan size and depth, with its reserve below.

    Go to Pans and depths
  2. Step 2: Fill in the specification

    Pans, worktop, reserve, openings and the model's limits.

    Go to the record
  3. Step 3: Call

    Read the specification out, or send it with your enquiry.

    Call (03) 5153 2650

Map each ingredient to a pan

Prep counters are specified in gastronorm (GN) pan sizes. A full GN 1/1 pan is 530 by 325 mm, and the other sizes are fractions of it: two GN 1/2, three GN 1/3, six GN 1/6 or nine GN 1/9 pans fill the same space. Common depths are 20, 40, 65, 100, 150 and 200 mm. A spec sheet gives the well as a count of one size, such as 8 x 1/3 or 16 x 1/6, and the deepest pan the well takes, which is often 150 mm.

Where pans and trays go on a prep counter
Part of the counterWhat the spec sheet statesWhat to check
The well or railHow many pans of which size, and the deepest pan it takes.Every ingredient has a pan of the right depth. The well is built to run with every opening filled by a pan or a divider, even where a pan stays empty.
DrawersThe pan size and depth each drawer takes, such as GN 1/1 at 100 mm or one GN 2/1 up to 200 mm, and often a weight limit.Your pans' depth and rim. On one maker's drawers, a pan's top lip can be no more than 5 mm high.
Cabinet belowShelves with their size and load limit, or slides for GN pans or 600 by 400 mm trays.Your reserve pans or trays fit as they are, below the load line.
WorktopThe cutting board's length, depth and material.Enough depth for your largest job, and whether the counter's stated depth includes the board.

GN is a standard footprint, so pans from different makers fit the same cabinets. Rims and corners still differ a little, so try one of your own pans in a drawer or a well before you buy.

For each ingredient, also note

  • Raw or ready to eat. Keep ready-to-eat food apart from raw food. Safe Food Australia (opens in a new tab), the guide to the food standards, says a board or utensil used to prepare raw food is not used for ready-to-eat food unless it has been cleaned, sanitised and dried.
  • Acidic or salty food. In storage, cut tomatoes, cut onions, vinegar, brine and some dressings go in sealed containers, because they can corrode a cabinet and its evaporator.
  • How much one stretch of service uses. Fill each pan with what you will use in a set period, not with the day's stock. The rest waits below.

The preparation surface

Size the worktop for the largest thing you make on it. Cutting boards on prep counters run from a strip about 220 mm deep on some salad counters to a board about 500 mm deep on some pizza tables. Boards may be polyethylene or a composite, and some pizza counters have a stone worktop. A composite board can warp from the difference in temperature and moisture between its top and its underside, so some boards are meant to be turned over on a schedule, as the manual says.

The board is a food contact surface. It is cleaned and sanitised before use, and between raw and ready-to-eat food. When you measure the space, check whether the counter's stated depth includes the board's overhang and any rear bumpers: on one maker's table they add almost 70 mm.

Customer-facing or back of house?

A counter in the kitchen only has to suit your staff. A counter where customers can see or reach the food also has to protect the food from them.

What changes when customers can see or reach the foodScroll sideways to see every column.
PointBack of houseCustomer-facing
Protecting the foodLids and night covers over the pans.Unpackaged ready-to-eat food on a counter sits behind a barrier. FSANZ (opens in a new tab) lists cabinets or wind shields for food on display.
Self-serveStaff serve.Self-serve food needs supervision, separate serving utensils and barriers against hands, sneezes and coughs. Safe Food Australia (opens in a new tab) says barriers should be placed at a height or angle that stops customers' coughs and sneezes landing on the food.
What the counter carriesA cutting board and lids.Some counters come with clear sliding doors or a sneeze guard over the serving area.
Where it standsAway from ovens, fryers and other heat.Also away from open windows, doors, fans and direct sun.

For noise and ventilation in a customer area, see the guide to choosing a commercial fridge format.

Reserve stock and how often the counter opens

The well holds what you are working from. The cabinet or drawers below hold the reserve that replaces it. For each ingredient, work out how many pans the busiest stretch of service uses, and plan room below for that many, covered and the same size as the well pans, so a change is one move.

  • Lids and night covers. A well is built to run with its lid closed whenever no one is working from it. On one maker's pizza bench, the rated room temperature drops from 40°C with the lid on to 32°C with it open. Some blown-air wells can run with their covers off for a short time at the peak, but left off, the well can ice up.
  • Doors and drawers. Keep openings few and short, and close each door straight after: a door left open lets the cabinet warm up. Self-closing doors and drawers help. Some counters ask for only one drawer to be opened at a time, so the counter does not tip.
  • Overnight. The well is for service. Overnight, the food goes into a fridge, or the pans are sealed and the cover closed, as the manual for the model says.
  • Count the openings. In your busiest hour, count how often the lid goes up and how often each door and drawer opens. That pattern goes in the specification.

The model's limits to ask the supplier for

Every counter is built for a range of conditions, and its spec sheet and manual say what they are. Ask for both before you buy, check them against your kitchen and your routine, and keep the manual where staff can find it. Where models differ, the manual for the model decides.

What to ask for, and why it matters
Ask forWhy it matters
Climate class or rated room temperatureA counter holds temperature only up to a certain room temperature and humidity. Spec sheets give it as a climate class, such as class 5 for 40°C at 40% humidity, or as a maximum room temperature. Ratings on prep counters run from about 24°C to 43°C, and some give a lower figure for when the lid is open.
Temperature rangeThe range the controller can be set to. Many counters top out at 5°C and some at 8°C, so where the range goes above 5°C, the setting you choose matters.
Pans, depths and dividersWhich pan sizes and depths fit the well, the drawers and the cabinet, whether pans are supplied, and whether every opening has to be filled.
What goes into the wellWells and storage counters hold food that is already cold. They are not built to cool it. Put food in already chilled, to the temperature the manual gives: below 5°C on some counters, 3°C or less on others.
Lid or night coverWhen it has to be closed, and whether it is insulated.
Load line and load limitsThe line in the cabinet that stock stays below, and the weight each shelf or drawer takes. Shelf limits run from about 20 kg on some counters to over 50 kg on others.
Ventilation and clearancesSome counters breathe from the front and need no gap at the back or sides. Others need a gap of up to 150 mm from the walls.
PowerThe supply on its rating label. Manuals usually ask for its own outlet, with no power board or extension lead. If it needs a new outlet or circuit, Energy Safe Victoria (opens in a new tab) says all fixed electrical installation work requires a licensed electrician, and that includes installing new wiring.
Cleaning instructionsWhat staff may clean, with what, and how often. Some manuals rule out a hose or a pressure washer, and some rule out cleaners containing chloride or bleach on stainless steel. Ask what daily cleaning the well needs: on some blown-air wells, the manual asks for the air ducts in the well to be cleaned every day, because food finds its way into them.
Condenser cleaningHow often the condenser needs cleaning, and who does it. On some counters it needs cleaning monthly and sits behind a cover, so it belongs in your maintenance plan.
Energy figureThe GEMS determination (opens in a new tab) that sets minimum energy rules for refrigerated cabinets does not cover open-top tables and saladettes for food preparation, so a counter with a pan well may have no registered energy figure. Ask for the maker's own figure and the conditions it was measured in.

For comparing running costs like for like, see the guide to commercial refrigeration energy ratings. For what staff can safely clean, see the guide to cleaning commercial refrigeration.

Check the counter is rated for the hottest the spot gets on a busy summer service. See the guide to commercial fridge climate classes for the questions to ask.

Choosing a pizza preparation bench

A pizza bench is a prep counter with a deeper worktop for dough and a raised or angled rail of topping pans behind it. Size it from your largest base, the number of toppings on the menu and how many dough trays a busy night needs.

What a pizza bench adds to the specification
PartWhat to check
WorktopDeep enough for your largest base. Some pizza benches have a stone worktop, others a board.
Topping railHow many pans, usually GN 1/3, and how deep, often 150 mm. On some rails, cold air blows above and below the pans.
LidAn insulated night lid. One maker's bench is rated for a 40°C room with the lid on but 32°C with it open, so the lid goes down between orders.
Dough storageSome pizza bases have slides for 600 by 400 mm trays, others take GN pans in drawers or have plain shelves. Count your dough trays and check they fit as they are.
Room temperatureIf the bench stands near the oven, measure how hot that spot gets. Some pizza benches are rated climate class 5, which is 40°C at 40% humidity.
ToppingsCut tomatoes, onions and other acidic toppings go into sealed containers when they come out of the rail.

Freezer drawers on a cook line

Freezer drawers under or beside a cook line keep frozen items within reach of the cook. They hold food that is already frozen, and frozen food stays frozen. Whether drawers or doors suit you better is covered in the guide to choosing a commercial fridge format.

  • Pans and depths. Freezer drawers take GN pans of a set depth. On one maker's range, the three-drawer model takes pans 100 mm deep and the four-drawer model 150 mm. Match the depth to what you portion into them.
  • Room temperature. Cooking equipment heats the air around it. Check the rated room temperature: one maker's freezer drawers are rated for rooms from 5°C to 43°C, and one chef base for up to 40°C.
  • Cooking equipment on top. Put cooking equipment only on a base built to carry it, such as a chef base, and keep within the weight limit it gives. The cooking equipment stands on its own legs, with the gap the manual asks for between the base's top and the heating elements, at least 100 mm on some bases, and a heat shield where the manual calls for one.
  • Drawer loads. Drawers have a weight limit, and some counters ask for only one drawer to be open at a time.
  • Short openings. Some freezer drawers close themselves, which keeps openings short in a rush.

Replenishing pans during a busy service

The temperature comes from the food standards (opens in a new tab). Potentially hazardous chilled food is kept at 5°C or below, unless the business can show another temperature is safe, and frozen food stays frozen. How you replenish the pans is part of keeping to that through a rush.

  1. Put food in cold. Food goes into the well already chilled. The well holds it cold; it is not built to cool it.
  2. Fill for a set period. Fill each pan with what the next stretch of service will use, and keep the rest below.
  3. Change the pan instead of mixing batches. Bring up a full, covered pan from the reserve and take the used one away, rather than adding fresh food to a pan already in use. FSANZ (opens in a new tab) advises against adding food to dishes on display, so batches do not mix.
  4. Keep the lid down between orders. Covers off for long periods let the well warm up, and on some wells it can ice up.
  5. Check the food, not only the display. FSANZ (opens in a new tab) says temperature gauges on equipment such as refrigerators measure the equipment's temperature, and to be sure of the food's temperature you should use a probe thermometer. A business handling potentially hazardous food needs a thermometer accurate to within 1°C.

If food has been out of refrigeration, FSANZ's 2-hour/4-hour rule (opens in a new tab) is a guide. The time food spends between 5°C and 60°C adds up. Under 2 hours, it can be used, sold or put back in the fridge. Between 2 and 4 hours, it can be used or sold but not put back. Over 4 hours, it is thrown away. For how a fridge reading differs from the food's temperature, see the guide to food temperature and fridge readings.

Production trays that work across cooling and holding equipment

Food made in batches often moves from the oven to a blast chiller, into storage and up to the counter. If one tray or pan size fits each step, the pan can move with the food. That is what gastronorm sizing is for: GN is a standard footprint, so pans from different makers fit the same cabinets, combi ovens, prep counters and chillers. Some kitchens work in 600 by 400 mm trays instead, so check each piece of equipment takes the size you use.

What each piece of equipment usually takesScroll sideways to see every column.
EquipmentWhat it usually takesWhat to check
Blast chillerGN 1/1 trays, and on some models 600 by 400 mm trays too. One takes 6 GN 1/1 or 600 by 400 mm trays on 12 runner positions 30 mm apart.The runner spacing against your deepest tray, and the load the chiller is rated for in one cycle.
Storage cabinetShelves, or runners and slides for GN pans. Some uprights have GN 2/1 shelves, 530 by 650 mm.Trays slide in as they are, below the load line.
Prep counter wellGN fractions, mostly 1/3, 1/6 and 1/9, up to about 150 mm deep. Some salad stations take GN 1/1.Whether production pans go straight into the well, or the food is portioned into well pans.
Pizza base600 by 400 mm dough trays on some, GN pans or shelves on others.Your dough trays fit the slides or shelves.
  • Shallow pans cool faster. FSANZ's tips (opens in a new tab) for cooling food quickly include dividing it into smaller portions in shallow containers, using rapid-cooling equipment such as a blast chiller, and letting air flow around the container.
  • Cooling has its own rule. FSANZ says cooked potentially hazardous food must be cooled from 60°C to 21°C in two hours or less, then from 21°C to 5°C in four hours or less, or by a different process the business can show keeps the food safe. Choosing that process and its equipment is covered in the guide to blast chilling, blast freezing and storage.
  • Covered and cleanable. Food in storage is covered, and pans and trays are food contact surfaces, cleaned and sanitised before use and between raw and ready-to-eat food.
  • Check the fit. Rims and corners still differ a little between makers, so try one of your own pans in each piece of equipment before you buy.

Where the counter sits in a kitchen layout

The counter goes where the food is put together. Keep it out of the heat: away from ovens, fryers and other equipment that gives off heat or steam, out of direct sun and warm draughts. Leave room in front for doors and drawers to open fully, and the ventilation gap its manual asks for. For the whole kitchen around it, see the guide to planning refrigeration in a commercial kitchen layout.

Prep counter specification

Prep counter specification

Fill in the first five parts from your menu and your busiest hour. Fill in the last part from the spec sheet and the manual the supplier gives you for the model.

Your answers stay on this open page. They are not saved or sent. Copy or print them before you leave.

The service

Main use
Who sees or reaches the food

Ingredients in the well

Raw and ready-to-eat food in the same well
Acidic or salty ingredients that need covered pans

Work surface

Worktop

Reserve stock

Base
Cooking equipment to stand on top

Opening and replenishment

How pans are replenished
Food in the well overnight

Model limits from the supplier

Choosing and supplying the counter

ABL supplies commercial refrigeration equipment. Send the specification with an enquiry from the equipment supply page, or have it in front of you when you call, and we can talk through the options with you. The hospitality refrigeration page covers kitchen refrigeration more widely. For a counter you already have that runs warm, see refrigeration repairs.

Sources (31)

Checked on 19 November 2026

Choosing a prep counter?

Send ABL your specification with an enquiry, or call and talk it through.

Filled in the record? Copy or print it first: it is not sent with a call or an enquiry.