Skip to the content

Open multideck or glass-door display fridge: access, conditions and energy

How an open multideck and a glass-door display compare on access, restocking, draughts, night blinds, tested energy and cleaning, with a record to fill in.

Last updated

An open multideck lets customers take stock without opening a door, so it suits fast self-service trade. It holds the cold in with a curtain of chilled air down the open front, and air conditioning, fans, an open entrance or sun on the cabinet can disturb that curtain. A glass-door display keeps the cold behind its doors, so it is less exposed to the shop, and compared like for like it usually uses less energy. The trade-off is a door to open for every pick and every restock. Decide for one product and one set of trading hours: how often stock is taken and restocked, where the cabinet will stand, how it is covered at night, what its energy figure is and what has to be cleaned.

How to use this guide

  1. Step 1: Check the spot

    Air conditioning, fans, the entrance and sun around where the display will stand.

    Go to Draughts and sun
  2. Step 2: Fill in the comparison

    Access, restocking, night cover, energy and cleaning, for one product and its hours.

    Go to the record
  3. Step 3: Call

    Read the record out when you call, or send it with an enquiry.

    Call (03) 5153 2650

How do an open multideck and a glass-door display compare?

An open multideck and a glass-door display, point by pointScroll sideways to see every column.
PointOpen multideckGlass-door display
Customer accessCustomers reach straight in. Nothing stands between the shopper and the product.Customers open a door for each pick, and see the product through the glass.
RestockingStaff load from the front, keeping stock behind the load line and clear of the air grilles.Staff hold a door open while they load, so each opening is best kept short.
Room in frontNothing swings out into the aisle.A hinged door swings into the aisle: about 400 to 750 mm on one maker's cabinets. Sliding doors open across the front.
How the cold is heldA curtain of chilled air runs down the open front. Air currents from air conditioning, fans and open doors disturb it.Doors close the front. In humid air the glass can fog, and some cabinets heat the glass or the door frames to keep it clear.
After trading hoursA night blind, where one is fitted, is pulled down over the front.The doors stay shut.
Energy testRun for 24 hours at climate class 3.The same, with each door opened six times an hour for 12 of the 24 hours.
Cleaning and serviceThe air grilles, the drain and, on a self-contained cabinet, the condenser, on the schedule in the manual.The same, plus door seals, hinges, closers and any heaters in the glass or the frames.

Customer access and restocking

Start with how the product moves. Count how many customers take from the display in your busiest hour, and how many times a day staff restock it. An open front suits a fast pick: there is nothing to open, and staff restock without holding a door. A door adds a step for every customer and every restock, and keeps the cold in between them. A shop owner's first question is often whether doors cost sales. In a study of two supermarkets, one fitted with open cases and one with glass-door cases, doors made no difference to product sales.

  • Load only stock that is already cold. A display cabinet holds chilled stock at temperature. It is not built to cool it down.
  • Keep to the load line. Stock, signs and baskets stay behind the line and clear of the air grilles. On an open cabinet, stock over the line breaks the air curtain.
  • Stay within the shelf load on the label or in the manual. On one maker's multidecks it is 50 kg a shelf.
  • Rotate as you restock. Bring the oldest stock to the front and put the newest behind it.
  • Move stock quickly from the coolroom or storage fridge to the display, so it does not warm up on the way.
  • With doors, keep each opening short. Every opening lets shop air in.

Draughts, air conditioning and sun around the display

An open multideck blows a curtain of chilled air down its front and draws it back in at the base. Air moving across the front disturbs that curtain and lets warm shop air in. A glass-door display is less exposed while its doors are shut, but both are built for the same room: under the GEMS determination (opens in a new tab), display cabinets are tested at climate class 3, which is 25°C and 60% relative humidity.

What to look for where the display will stand
Around the displayWhy it matters
Air conditioning outlets and returnsAir from an outlet should not blow at the cabinet's front, and a return should not draw air across it. Check the shop's air conditioning keeps the room within the cabinet's class on a hot day.
Ceiling and pedestal fansA fan moving air past the front does the same. One maker designs for air moving past the front at no more than 0.2 metres a second.
An entrance or an open windowEach time the door opens, outside air moves through the shop. See the section on a display near an entrance.
SunSun through a window, a glass shopfront or a skylight is heat on the stock and the cabinet. Check the spot in the morning and in the afternoon.
Ovens, heaters and hot displaysKeep refrigerated displays away from heat sources such as ovens, heaters, heated cabinets and hot pipework.
A small or closed-in spaceA self-contained display puts the heat it removes into the room. In a small room without ventilation it warms the room and uses more power.

For food on display, FSANZ (opens in a new tab) advises using cabinets or wind shields and keeping food away from open windows, doors and fans. Potentially hazardous chilled food is kept at 5°C or below, unless the business can show another temperature is safe, and frozen food stays frozen. For what a room warmer than the test room means for a cabinet, see the guide to commercial fridge climate classes. For where a display's heat goes, see the guide to remote or self-contained display refrigeration.

A display near an entrance

A spot by the door is seen first, and it is also a hard spot for an open multideck. Each time the entrance opens, outside air moves into the shop, and a glass shopfront lets sun onto the cabinet. An open door is one of the places a display cabinet is not meant to stand, and a maker may not stand behind how a cabinet performs there, or in strong sun.

  • Set the display back from the door and out of the path of air coming in, rather than facing the opening.
  • Watch the sun on the spot across the day, through the door and the shopfront glass.
  • Keep the entrance door shut when it does not need to be open.
  • Consider a glass-door display for that spot. Its doors keep the draught off the stock between customers, though the glass can fog where humid air reaches it.
  • Read and record the display temperature at the busiest time of day, not only first thing in the morning.
  • Note the draughts, the sun and the door before you buy, and tell us about the spot when you ask about a cabinet.

Night blinds on open displays

A night blind is a fabric blind on a roller that pulls down over an open front when the shop is closed. It keeps warm room air out overnight, which helps save energy and hold the product's temperature, and it hides the stock. Not every open cabinet has one. On some it is an option when you buy, and blinds can also be fitted to cabinets already in use. Some cabinets offer a roller shutter that locks instead, for security.

  1. Restock before close, so the blind stays down once it is down.
  2. Pull the blind right down and fasten it the way the manual shows. A blind keeps air out only if it reaches the bottom and sits close at the edges.
  3. Turn the cabinet lighting off after hours, where it has its own light switch or timer.
  4. At opening, raise the blind before customers arrive, then read and record the display temperature.
  5. Name who does it on each shift, so it happens at the late close and the early open.

A blind that is torn, stops short or catches on stock lets room air in. Note it and tell us at the next service. Do not adjust the roller or its spring: a spring under tension can cause injury if it lets go.

Comparing energy figures like for like

Refrigerated display cabinets are covered by the GEMS (Refrigerated Cabinets) Determination 2024 (opens in a new tab). They have to meet a minimum energy efficiency level, and each model is tested to one method, so the figures on its registration and specification sheet can be compared. Compare them only between cabinets tested alike. Match these first.

What to match before comparing two display cabinets
MatchWhat it meansWhere to find it
Product classIntegral or remote, chiller or freezer, and vertical or horizontal. An open and a glass-door multideck can share a class, such as an integral vertical chiller.The registration and the specification sheet.
Temperature classThe class of test packs the cabinet held. M1 means the warmest pack stayed at 5°C or colder. M2 allows 7°C and H1 allows 10°C.The specification sheet, sometimes written with the climate class, such as 3M1.
Test roomDisplay cabinets are tested at climate class 3: 25°C and 60% relative humidity.Set by the determination.
Daily energyKilowatt-hours per 24 hours in the test.The specification sheet and the registration.
Display areaThe total display area in square metres. A larger display area is allowed more energy, so divide the daily energy by the area to compare cabinets of different sizes.The specification sheet.
Stars, if quotedStars compare the cabinet's energy with a standard cabinet of its class and display area. Where a supplier quotes stars, the determination sets how they are worked out.The supplier.

Here is what that looks like on real figures. One maker sells the same full-height multideck either open or with hinged glass doors: the same widths, the same display area and the same test class, 3M1. Across its four widths, the open version is rated at between about three and five times the daily energy of the door version. Another maker's cabinets will differ, so compare the figures for the models you are offered and check the manual for each.

The test opens each door of a glass-door cabinet six times an hour for 12 of the 24 hours. Count how often your doors would open in your busiest hour and set that beside the test. To turn a daily figure into a running cost, see the guide to commercial refrigeration energy ratings and running costs.

Adding doors, blinds or aerofoils to an open cabinet you have

Transparent doors fitted to an open cabinet can cut the cold air it loses, though not as well as a brand-new cabinet. Aerofoils along the shelf edges, which guide the air curtain down the front, can be a cost-effective way to reduce the loss. Ask for evidence that the cabinet still holds its temperature class with the retrofit fitted, and remember that a door or blind works only if it fits closely at the edges. Ask us to look at the cabinet before you buy one.

Choosing grab-and-go refrigeration

In a grab-and-go display, customers serve themselves, usually from packaged food and drinks. The display holds them cold. Your product controls do the rest, so plan them at the same time as the cabinet.

  • Packaged, or protected. For unpackaged food on self-service, FSANZ (opens in a new tab) says you must provide separate serving utensils and barriers to protect food from people's hands, sneezes and coughs, and supervision so you can act quickly if someone contaminates it.
  • Cold before it goes in. Chill the food before it goes on display.
  • Date marks and rotation. Check date marks, sell older food first and discard food past its use-by date, as FSANZ (opens in a new tab) advises.
  • A replenishment plan. Decide how often staff restock at peak and where the next batch waits. Small, frequent restocks from a coolroom or storage fridge keep the display within its load line, because an overstocked display does not hold temperature.
  • Temperature records. FSANZ suggests keeping records of the times and temperatures food is displayed at, to make sure the display equipment is working and temperatures are safe. A food service business handling unpackaged, ready-to-eat, potentially hazardous food may need to substantiate its food safety controls for displaying food under Standard 3.2.2A.

With those controls set, open or glass-door is the comparison on this page, for that product and those hours. For an alarm that warns when a display drifts, see the temperature monitoring page.

Supermarket backstock or display: two different jobs

A display cabinet is built to show cold stock to customers and hold it at temperature. Backstock needs somewhere to wait in bulk, cold, until it goes on display: a coolroom or storage cabinets behind the scenes. The GEMS determination treats them as different equipment.

Display and backstock compared
PointDisplay cabinetBackstock storage
Its jobShow stock to customers and hold it cold.Hold stock cold in bulk until it is needed.
Who opens itCustomers all day, and staff to restock.Staff only.
What goes inStock kept below the load line.Cartons and crates, on shelves.
How it is ratedAs a display cabinet, at climate class 3.A storage cabinet is rated light, normal or heavy duty. A coolroom is designed for its site.
Size it forWhat sells between restocks, with room left for the air to move.What arrives in one delivery, plus what the display needs until the next.

Keep the display as a display. Stock packed above the load line or in front of the grilles does not stay cold, and the cabinet works harder. Move stock out from the backstock in small, quick loads. For choosing between a coolroom and cabinets for backstock, see the guide to a coolroom or commercial fridges. For rotation and picking inside a coolroom, see the guide to laying out a coolroom for stock picking.

Cleaning and service access

Both kinds need cleaning and servicing, and the manual for the model sets what and how often. Ask for the manual before you buy, and make sure a technician can reach the parts that need service where the cabinet will stand.

What needs attention on each kind of display
PartOpen multideckGlass-door display
Air grillesThe discharge grille along the top, often a honeycomb, and the return grille at the base. A dirty honeycomb makes the cabinet perform poorly, so it is cleaned on a schedule.Air grilles inside the cabinet, kept clear of stock.
DrainDefrost water runs to a drain. A blocked drain can make the cabinet leak.The same.
CondenserOn a self-contained cabinet, cleaned often: every one to two months on different makers' cabinets. On some it sits behind a front grille, so keep the front clear for service.The same.
DoorsNone.Door seals, hinges and self-closers, and any heaters in the glass or the frames.
Service visitAt the interval the manual sets: on one maker's multidecks, at least every 12 months.The same.

Your staff wipe the cabinet down and keep the grilles and the front clear. Leave the gap behind the cabinet that the manual asks for, 50 mm on one maker's multidecks and 80 mm on another's, so the condenser can draw in room air. Everything behind the panels and grilles is for the service visit: see the refrigeration maintenance page. A remote cabinet has no condenser of its own in the shop, and the guide to remote or self-contained display refrigeration covers where its plant goes.

Open or glass-door display comparison

Open or glass-door display comparison

Fill this in for one product and one set of trading hours. Take each energy figure from the cabinet's specification sheet or registration, and compare the figures only when the product class and the temperature class match.

Your answers stay on this open page. They are not saved or sent. Copy or print them before you leave.

The product and the hours

How it is sold
Temperature class it needsThe warmest test pack the class allows
Where backstock waits

Where it would stand

Air conditioning outlet or fan blowing towards it
Sun on it at any time of day
Oven, heater or hot display nearby

Option A: open multideck

A: night blind fitted or available

Option B: glass-door display

B: doors

Like for like, and the routine

Same product class and temperature class for A and B
Leaning towards

What to bring us

Bring the comparison record and a photo of the spot, or read them out when you call. We talk through the draughts, the sun, the space in front and what the product needs. ABL supplies commercial refrigeration equipment: see the equipment supply page. If a display you already have is not holding temperature, see the refrigeration repairs page.

Sources (12)

Choosing between an open and a glass-door display?

Send ABL your comparison record with an enquiry, or call and talk it through.

Filled in the record? Copy or print it first: it is not sent with a call or an enquiry.